Generac Power Systems 005325-0, 005324-0 owner manual Elbow 90D 3/4 NPT

1	026812	2	ELBOW 90D 3/4 NPT
2	075580	1	FLANGE FUEL INLET
3	0G1397	1	FUEL REGULATOR 1.6L REWORK
4	039253	2	SCREW HHC M8-1.25 X 20 G8.8
5	022145	2	WASHER FLAT 5/16 ZINC
6	022129	4	WASHER LOCK M8-5/16
7	045771	2	NUT HEX M8-1.25 G8 YEL CHR
(1) 8	0F1570	1	BODY CARBURETOR ASSEMBLY
9	0A6344	1	BARBED EL 90 1/8NPT X 3/8
10	0C5210	1	HOSE 3/8 ID LOW PRES OIL/WATER ( 8“LG)
11	025424	1	NIPPLE PIPE 3/4 NPT X 6
12	0C5210	1	HOSE 3/8 ID LOW PRES OIL/WATER (13“LG)
13	0A5547	1	COVER AIR CLEANER
14	0G0321	1	HOSE COOL 5/8"ID 250#WP ( 3”LG)
15	0D1509	1	DECAL INLET PRESSURE

(1)	16	0E0591	1	ADAPTER CARB. TO AIR CLNR
	17	059402	1	FILTER ELEMENT
	18	037561	1	NUT WING 1/4-20 NYLK
	19	0E1028D	1	ASSY CARBURETOR 1.6L
	20	059401	1	CARBURETOR GASKET
(1)	21	091526	4	SCREW PPHM M5-0.8 X 12 ZNC
(1)	22	049226	4	WASHER LOCK M5
	23	026915	2	NIPPLE CLOSE 3/4 X 1.375
	24	062522	1	STUD TH 1/4-20 X 3 G2 ZNC FULL
	25	022127	1	NUT HEX 1/4-20 STEEL
(1)	26	0E1339	1	PIN SPRING 3/16 X 5/8
27 **		050279	1	DECAL FUEL INLET NG
		050280	1	DECAL FUEL INLET LPG
	28	030795	2	SCREW HHC 5/16-18 X 1 G5
	29	0F6155	1	HARNESS FUEL JUMPER SINGLE REG
(1)	30	0E1104	1	GASKET AIR CLEANER ADAPTER
(1)	31	0E0668	1	O-RING 2-028 1.38 X 1.50 X .06
(1)	32	0E0590A	1	VENTURI 20MM
(1)	33	0C5133	1	O-RING 29.82 X 2.62
(1) 34		0E0665	1	SCREW THROTTLE PIN STOP
(1) 35		0E1108	1	THROTTLE ARM REWORK
(1)	36	033138	1	SCREW HHM #10-32 X 5/8
(1)	37	022152	1	WASHER LOCK #10
(1)	38	0E0645	1	LEVER THROTTLE STOP
(1)	39	034339	1	BARBED EL 90 3/8 NPT X 5/8
	40	059194	1	HOSE 5/8 ID LPG & NG (16” LG)
	41	057823	2	CLAMP HOSE #10 .56 - 1.06
	42	048031G	2	CLAMP HOSE BAND .41
(1)	43	039450	1	BARBED EL 90 3/16 X 1/8
	44	029470	1	HOSE 3/16 ID FUEL LINE (22 “LG)
	45	059057	1	HOSE 3/4 ID SAE-30R2 ( 3”LG)
	46	0G1461	1	HOSE BARB TEE 3/4" NYLON
	47	0F3994	1	PCV VALVE 2.5L FORD
	48	0G1462	1	HOSE BARB REDUCER 5/8"-3/8"ID
(1)	49	0E0568	1	SHAFT, THROTTLE 1.5L
(1) 50		0E0527	1	THROTTLE VALVE PLATE 27MM
(1)	51*	025105	1	SCREW RHMS 6-32 X 1/4 ZINC
(1)	52	0E0991	1	SEAL, SHAFT COVER
	53	048031P	2	CLAMP HOSE BAND .88"
	54	048031J	4	CLAMP HOSE BAND .63
	55	048031L	5	CLAMP HOSE BAND 1.0"
	56	035579	1	BSHG RDCR HEX 1/4 TO 1/8

(1) INCLUDED IN ITEM 19 (CARBURETOR ASSY )

NOTES:

1. REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR NATURAL GAS APPLICATION.

2. TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB, HOSE CLAMP (I/N 41) AND HOSE (I/N 40) FROM “OUT-1” TO “OUT-2”. REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE FROM DEBRIS DURING RECONFIGURATION PROCESS.

3*. APPLY LOCTITE TO I/N 51 BEFORE THREADING INTO I/N 49.

4**. FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N 050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM 27).

5. WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SETTINGS MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL SECTION FOR MORE DETAILS.