Generac Power Systems 005259-1, 005260-1 owner manual ‹ Changing Engine OIL, ‹ Spark Plugs

Page 18

Standby Generator Sets

Maintenance

‹CHANGING ENGINE OIL

Refer to maintenance performed by authorized service facilities for engine oil and filter change frequencies.

Drain the oil while the engine is still warm from run- ning. This means warm up the engine, shut it down and drain immediately as follows:

1.Remove OIL DRAIN HOSE from its retaining clip.

2.Loosen and remove OIL DRAIN HOSE CAP. Drain oil completely into suitable container.

3.When all oil has drained, install and tighten OIL DRAIN HOSE CAP, and re-install into its retaining clip.

4.Turn OIL FILTER (Figure 10.2) counterclockwise and remove. Properly dispose of old filter.

Figure 10.3 – Engine Air Cleaner

Air Cleaner

Figure 10.2 – Oil Filter

Oil

Filter

5.Apply light coating of new engine oil to seal of new oil filter.-Install FILTER and tighten by hand only.

DO NOT OVER TIGHTEN.

6.Remove OIL FILL CAP. Add recommended oil (see

SPECIFICATIONS). DO NOT FILL ABOVE THE DIPSTICK “FULL” MARK. Crankcase oil capacity is 4.0 U.S. quarts (3.8 liters).

After refilling the crankcase with oil, always check oil level on dipstick. NEVER OPERATE ENGINE WITH OIL BELOW THE DIPSTICK “ADD” MARK.

7. Start engine and check for oil leaks.

(Doors Removed for Clarity)

‹SPARK PLUGS

Reset the spark plug gap or replace the spark plugs as necessary (Figure 10.4).

1.Clean the area around the base of the spark plugs to keep dirt and debris out of the engine. Clean by scraping or washing using a wire brush and commercial solvent. Do not blast the spark plugs to clean.

2.Remove the spark plugs and check the condition. Replace the spark plugs if worn or if reuse is questionable. See the “Service Schedule,” Section 6, for recommended inspection.

3.Check the spark plug gap using a wire feeler gauge. Adjust the gap to 1.07-1.17 mm (0.042- 0.046 inch) by carefully bending the ground elec- trode (Figure 10.4).

Figure 10.4 – Setting the Spark Plug Gap

SET PLUG GAP AT 1.07 - 1.17 mm

(0.042 - 0.046 inch)

‹ CHANGING THE ENGINE AIR CLEANER

 

‹ COOLANT CHANGE

To replace the engine air cleaner, remove the air cleaner cover and replace the air filter making sure it is positioned properly before reattaching the cover (Figure 10.3).

See the “Service Schedule,” for air cleaner mainte- nance.

Every year, have an Authorized Service Facility drain, flush and refill the cooling system. See “Specifications” for cooling system recommendations.

10-3

04/06

0 .Rev Maint012

Image 18
Contents 35kW Models 005259-1 Standby Generator Sets Table of Contents  Warning   Electrical Hazards  Authorized Service Dealer Location ‹ Operation and Maintenance‹ HOW to Obtain Service IntroductionIdentification Record ‹ Data LabelEquipment Description Engine OIL RecommendationsCoolant Recommendations Engine Protective Devices ‹ Natural GAS Fuel System Fuel System‹ Fuel Requirements ‹ LP Fuel SystemSpecifications ‹ Reconfiguring the Fuel System ‹ Cold Weather KIT‹ 3-PHASE Alternators Alternator Power Winding Connections‹ FOUR-LEAD, SINGLE-PHASE Stator Generator AC Lead ConnectionsInstallation Preparation Before START-UPInitial Inspection for QT Genset Startup START-UP Checklist ‹ Preparation for START-UP‹ START-UP Inspection ‹ Engine START-UP and Transfer Operating Unit with Manual Transfer SwitchGenerator Control Operation ‹ Retransfer and ShutdownCooling System Checking Fluid LevelsMaintenance Owner Operator can Perform ‹ Changing the Engine AIR Cleaner ‹ Coolant Change ‹ Changing Engine OIL‹ Spark Plugs ‹ Battery Miscellaneous Maintenance‹ Cleaning the Generator ‹ Battery MaintenanceService Schedule KW 150 KW Standby GAS Engine Driven Generator SetsMaintenance Level 11-3 11-4 Troubleshooting Guide Problem Cause CorrectionStandby Generator Sets Standby Generator Sets Standby Generator Sets Page PAN CB Conn BOX Page UL Circuit Breaker QJ-2P Page Instr Hypot Test not Shown Page Components Included in 0F9696E Page Components Included in 0G1290E Page Weldment Frame 2.4L C2 Page Battery Tray C1 CPL Page Gasket Bosch 32 Page Engine 2.4L G2 Rework Page Weldment Radiator Support 2.4L Page Flange Fuel Inlet Page Rear Wrap C2 CPL Page Bracket Muffler Page Page Page Page Page Page Page Page Page Page Page Page Page C2 Units Standby Generator Sets Warranty

005260-1, 005259-1 specifications

Generac Power Systems has established itself as a leader in the power generation industry, particularly with its innovative range of home backup generators. Among its popular models are the Generac 005259-1 and 005260-1, both of which reflect the company’s commitment to engineering excellence, reliability, and user-centric design.

The Generac 005259-1 is a 22 kW air-cooled standby generator that operates on either natural gas or liquid propane, providing ample power for essential home appliances during an outage. This model features a robust V-twin engine, which not only ensures durability but also enhances performance in various weather conditions. Its Quiet-Test technology allows the generator to run a self-test at a lower RPM, reducing noise and conserving fuel while still ensuring that the unit is operational.

On the other hand, the Generac 005260-1 serves as a powerful 24 kW generator, boasting an advanced control system designed for ease of use. This model features the Mobile Link™ technology, which enables users to monitor their generator’s status from anywhere using a smartphone, tablet, or computer. This ensures homeowners can stay informed about their power system’s readiness without having to physically inspect the unit.

Both models are equipped with Generac's True Power™ technology, which provides clean and stable power suitable for sensitive electronics, ensuring that appliances and devices run smoothly even during outages. Additionally, they come with a robust weather-resistant enclosure that protects them from the elements, ensuring long-lasting performance.

Installation of both units can be streamlined with their adaptable mounting pads and flexible connection options. Furthermore, Generac provides comprehensive support services, including warranty programs and maintenance plans, ensuring customers have access to the assistance they need post-purchase.

Overall, the Generac 005259-1 and 005260-1 generators exemplify reliability and innovation, making them excellent choices for homeowners seeking peace of mind when it comes to power outages. With advanced features, user-friendly technology, and powerful performance, they exemplify Generac’s dedication to delivering quality power solutions.