Flowtron Outdoor Products MT-350 owner manual Rules for Safe Use, Placement, Assembly

Page 3

Rules for Safe Use

1. Use outdoors only. Install the unit a minimum of ten feet from buildings and other structures.

Placement

Your Mosquito PowerTrap is site specific and place- ment is critical for successful results. To properly lo-

cate your unit in your yard, read the accompanying booklet “the Fine Art of Trapping Mosquitoes” and follow its guidelines regarding trap placement,

Assembly

(MT-300 series only)

1.Insert tank support strap into openings in tank

stand as shown.

See Figure A.

Tank Support

Tank Stand

Strap

Openings

Figure A

Connect Propane Regulator

1. Remove the plastic dust cover from your propane tank valve.

2. Screw the propane regulator coupling located on the end of the propane hose onto the tank valve by turning the black threaded coupling clockwise until tight. Hand tighten only. See Illustration 4.

2. Never place fingers or insert any ob- ject into the unit while it is operating.

3. Always disconnect unit from its pow- er source and wait for unit to cool before handling, moving or servicing.

4. This device was designed for use

Your Flowrtron Mosquito PowerTrap emits a plume of octenol-enhanced carbon dioxide which mosquitoes follow in their search for a blood meal. Mosquitoes fly up-wind toward the source of the plume in their at- tempt to locate a host. Since the direction of the plume is dependent upon the direction of the wind, your unit should be positioned so it’s

attractant outlet faces downwind.

Female mosquitoes also feed on moisture laden nec- tar and fruit juices when not in search of a blood meal. They are usually found in shade; around flow-

On the underside of the tank stand, loosen the two hex nuts located on the screws which extend from the sides of the base plate. Place the slots at the ends of the tank support strap over the screws and secure by tightening the two nuts. See Figure B.

Base Plate

Screw & Nut

Tank Strap

Note: Gas will not flow unless connection is tight.

Tighten by hand only.

 

Using a wrench or

 

other tool could

 

damage the regulator

 

coupling and could

 

cause a gas leak.

Illustration. 4

 

WARNING

with propane gas. Never attempt to use any other fuel, including liquid fuels or natural gas. Fire or damage to your Flowtron PowerTrap could result.

5. Always operate the unit in an up-

ers, trees, bushes and other vegetation; and adjacent to standing water.

For best results locate your unit 20 to 40 feet away from areas of human activity in a location near (but not in) bushes, wooded areas, or adjacent to standing water (other than swimming pools). Select a location which will result in the carbon dioxide plume blowing

toward the area where mosquitoes are likely to hide and emerge. A proper location will ensure that

(2 places) Figure B

2.Insert one end of the

post into the post opening at the front of the tank stand. Insert opposite end of post into the post opening located at the bottom of the Flowtron

Mosquito PowerTrap®. Align unit in relation to the tank stand. See Illustration 2.

Place a 20 lb. tank on the tank stand and install tank wrap around the tank.

Check for gas leaks by wetting the connec- tions with a solution of soap and water and watching for bubbles. If bubbles form or if a bubble grows larger, there is a leak and connection must be tightened.

WARNING

Check for gas leaks every time you disconnect and reconnect a gas fitting.

right position to prevent damage to the CO2 generator.

6. Do not abuse the power pack. Never carry the power pack by its cord or yank it to disconnect it from a receptacle. Keep power cord away from heat, oil and sharp edges.

7. Never connect the unit to a

mosquitoes encounter the plume and follow it up- wind to the Flow t ron Mosquito PowerTrap before they detect the presence of humans.

See Illustration 1.

 

Illustration 1

Prevailing wind direction

 

 

Plume

 

 

Attractant

 

Outlet

3.Install catch tray by first inserting the rear of the tray into the housing.

Then push in upper part of the latch and raise

front of catch tray into place. See Illustration 3.

4. Position and screw pow- er pack to either an out- side or inside wall adja- cent to a electrical outlet (screws not provided).

Tank Strap

Post

Tank

Cap

Tank

Wrap

Be sure there are no sparks or open flame in the area when you check for leaks.

Do not use a liquid propane tank with a damaged valve. Have dented or rusty propane tanks checked by your propane supplier.

Only use regulator supplied with your Flowtron PowerTrap.

3.Place tank cap on top of tank.

4 . Move your unit to the desired location in your

battery or other D.C. voltage. Such an attempt will damage your unit.

8. Store indoors when not in use. Remove propane tank from unit be- fore storing and store tank outdoors in a well ventilated space.

HOUSE

PATIO 20 – 40 ft.

SOURCE OF

 

 

INSECTS

Run the low voltage wire either above or below ground from the power pack to the unit. plug the low voltage wire into the power cord connector lo- cated at the bottom of the Flowtron Mosquito PowerTrap®. Plug the power pack into the elec- trical outlet.

See Illustration 5.

InstallTank

screwStand

and Tank Cover washer Stand

Illustration 2

Push

illustration 3

yard. Remove catch tray and grasp housing as shown.

See trap “Placement” in- structions on pg. 4.

(MT-300 series only)

Page 4

Page 5

Image 3
Contents Accessories Trouble Shooting ChartMT-350 Octenol Cartridge MaintenanceTable of Contents To Install the Octenol CartridgePlacement AssemblyRules for Safe Use Operation How Your Flowtron Mosquito PowerTrap WorksOff/Reset manual off Your Flowtron Mosquito PowerTrap

MT-350 specifications

The Flowtron Outdoor Products MT-350 is a highly effective mosquito and insect control solution that combines advanced technology with user-friendly features to create a pest-free outdoor environment. Designed specifically to meet the needs of homeowners, this electric insect killer operates efficiently while ensuring safety and ease of use.

One of the standout features of the MT-350 is its powerful 40-watt bulb, which attracts a wide variety of flying insects, including mosquitoes, flies, and gnats. The ultraviolet light emitted by the bulb lures pests into the device, where they are then trapped on an internal killing grid. This technology ensures maximum efficiency in reducing insect populations, allowing you to enjoy your outdoor spaces without the annoyance of pesky bugs.

The MT-350 is engineered for durability, constructed with weather-resistant materials that can withstand outdoor conditions. Its robust design ensures longevity, making it a reliable addition to your backyard setup. Furthermore, its compact and sleek design allows for easy placement in various outdoor areas, such as patios, decks, and gardens.

One of the notable characteristics of this insect trap is its ease of operation. The MT-350 does not require chemical insecticides, making it a safe choice for families with children and pets. Simply plug the device in, and it will start working immediately, providing around-the-clock insect control.

Maintenance is also straightforward with the MT-350. The unit features a removable collection tray that captures the insects, making it easy to clean and dispose of them. This hassle-free maintenance allows users to focus more on enjoying their outdoor activities rather than worrying about pest control.

In terms of energy efficiency, the MT-350 is designed to consume minimal electricity, making it an eco-friendly option for anyone looking to keep their outdoors free from insects without incurring high energy costs.

In summary, the Flowtron Outdoor Products MT-350 is an innovative and effective solution for outdoor insect control. Its powerful UV light, durable construction, ease of use and maintenance, and energy efficiency make it an excellent choice for anyone looking to enhance their outdoor experience. With this device, you can create a more enjoyable and comfortable environment for gatherings, relaxation, and recreation in your backyard.