![](/images/new-backgrounds/1092577/925777x1.webp)
Set-Up
•Make sure the back of the shredder is at least 2" (5 cm) away from walls or furniture to ensure suffi- cient ventilation.
•Open the cabinet door and pull the waste basket (D) completely out of the cabinet.
•Put plastic waste bag in basket (sample bags provided). Allow bag edges to overhang. Contact Fellowes to order more bags (part # 36054).
•Slide the waste basket into the cabinet and shut the cabinet door (A).
•Plug the power cord into a convenient outlet.
•Store use and care manual in slot (M) inside cabinet door (A).
Operation
Control Switches
To empty waste basket
If basket full light (J) is on, follow these steps until light turns off.
1• Press Turbo Jam Release Button (F) to finish shredding any paper in the paper entry.
•Press the off [O] button.
•Open the cabinet door (A) and pull out the waste basket (D).
•Remove the full bag and replace with a new bag.
•Slide the waste basket (D) into the cabinet and shut the cabinet door (A).
•Press and hold the reverse [R] button for a few seconds to clear paper shreds that have collected under
2cutting cylinders.
•Alternate between Turbo Jam Release Button (F) and reverse [R] for a few seconds in each position. Caution: The shredder may be damaged if you alternate too rapidly between forward and reverse.
•Unplug shredder, open cabinet door (A) and remove wastebasket (D).
3• Carefully clear any paper shreds that have collected on under side of paper entry (B).
I |
| J |
| K |
F
G
H
Control Switch (H)
IAUTOMATIC
Turns on the
OOFF
Turns off the
RREVERSE
Runs shredder in reverse mode. Press and hold to activate.
Turbo Jam Release Button (F) Runs shredder when button is held down.
Caution: Model
To clear a paper jam
•If paper jam light (I) is on, follow these steps until light turns off.
•Check the waste basket (D) and empty the bag if full.
•Press and hold the reverse [R] button to back paper out of the paper entry (B). Try pulling gently on the paper to remove it from the shredder.
•Alternate between forward and reverse, as needed, until the jam clears:
–Press and hold the manual forward button (F) for a few seconds.
–Press and hold the reverse [R] button for a few seconds.
•Continue alternating between forward and reverse until the jam clears.
Caution: The shredder may be damaged if you alternate too rapidly between forward and reverse.
Troubleshooting Lights
Ready Light (G) | Paper Jam (I) | Basket Full [J] | Door Ajar (K) |
(Green) Shredder is in | (Red) Shredder is | (Red) Waste basket is | (Red) Cabinet door is |
automatic start mode. | jammed (e.g., too much | full or paper has col- | open. |
| paper fed at one time). | lected under cutting |
|
|
| cylinders. |
|
For convenience and energy savings, your shredder is equipped with an
(O). This means that when the control switch (H) is in the automatic [I] position, the shredder will start running when you put paper into it and stop a few seconds after the paper has passed through.
CAUTION: The
To shred
Press control switch (H) to automatic [I] position. Green ready light (G) should turn on.
PAPER
•Feed paper straight into entry (O), releasing when shredder begins shredding; see Product Profile for limits on paper width, shreddable items, sheet capacity, etc.
•Press control switch to off [0] position after cutting has stopped.
CDs, DVDs (220-2/C-220 only)
•Hold CD or DVD at the edge and feed one at a time, straight into entry (E) releasing when shredding begins. Shredder will stop when item has passed through entry. CDs and DVDs will be shredded into small particles.
CAUTION: Do not hold CD or DVD with finger through the center ring while feeding into shredder.
Maintenance
Empty waste basket regularly to ensure the smooth functioning of the cutting cylinders. The shred- der will not operate when the basket is full.
Oil
Use Fellowes Powershred Lubricant #32250 or other
CAUTION: Do not use flammable synthetic oil,
To oil the cutting cylinders
•Lift paper entry flap (N) and apply oil over full width of cutting cylinders through the paper entry (B).
•Press and hold the Turbo Jam Release Button (F) for at least 3 seconds.
•Press and hold the reverse [R] button for at least 3 seconds.
•Repeat the forward/reverse sequence 3 or more times.
•Store oil bottle in slot (L) inside cabinet door (A).
4 | 5 |