Install back panel | Elkay EDFP217RAC, EDFP217C instruction

EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC

INSTALLATION INSTRUCTIONS

1. Wall should already be framed for the fountain using the positioning dimensions shown in Figures 3, 4, 5, or 6. Shown dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions are required for compliance with ANSI Standard A117.0.

2. Install rough-in plumbing as shown in Figures 3, 4, 5, or 6. Waste line should extend a minimum of 2" (51mm) through the back panel. Run the supply water inlet line through the back panel. Install a service stop (not provided). Turn on supply water and flush thoroughly.

3. Install back panel.

EDFP217C: Place the upper edge of the panel above hanger bracket.

EDFP217C W/MOUNTING PLATE: Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it engages the mounting plate. Be sure back panel is firmly engaged before releasing it.

3.Remove bottom access panel from fountain basin and save the screws.

EDFP217C: Install the fountain to the back panel and wall using (4) 5/16" x 2" long lag bolts and washers (not provided) through holes in back panel. Tighten securely.

EDFP217C W/WALL PLATE: Install the fountain to the back panel using (4) 5/16" x 3/4" long screws and washers (provided) through holes in back panel. Tighten securely.

4.Remove elbow from end of p-trap and attach it to drain tube. Reattach elbow to p-trap and cut waste tube to required length using plumbing hardware and trap as a guide.

5.Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the strainer. Turn on water supply and check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS

DAMAGE TO THE O-RINGS MAY RESULT.

6.These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not covered by warranty.

7.Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 10 by using a small screwdriver through the small hole in the push button item 3 (See Fig. 11). Clockwise adjustment will raise stream height and counter-clockwise will lower stream height. For best adjustment stream should hit basin approximately 6-1/2" (165mm) from bubbler.

8.Replace bottom access panel to fountain using the screws provided. Tighten securely.

TROUBLE SHOOTING AND MAINTENANCE

1.Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire. CAUTION: Do not file or cut orifice materials.

2.Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 7 stated above.

3.Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it reaches a positive stop, approximately 3/4".

97705C (Rev. J - 8/07)

PAGE 6

EDFP217C, EDFP217RAC specifications

The Elkay EDFP217RAC and EDFP217C are innovative and stylish combinations of drinking water systems designed for modern public spaces. Known for their sleek design and user-friendly features, these water dispensers exemplify Elkay's commitment to quality and sustainability.

One of the standout features of the EDFP217RAC and EDFP217C is their advanced filtration technology. These models utilize an integrated water filtration system that reduces contaminants and improves taste, ensuring the water served is clean and refreshing. The filters are easy to replace and are designed to last, providing an eco-friendly alternative to single-use plastic bottles.

Both models are equipped with an Energy and Water Conservation technology that not only saves resources but also reduces operating costs. The LED indicators on the front display the status of the filter, making maintenance straightforward for facility managers.

The touchless activation feature enhances hygiene, particularly in high-traffic public places. Users can simply place their water bottle or cup under the spout to activate the flow, reducing the risk of cross-contamination. This feature is especially relevant in today's health-conscious environment, where minimizing contact with surfaces is a priority.

Ergonomically designed, the Elkay EDFP217RAC and EDFP217C boast a user-friendly interface with a spacious dispensing area, accommodating a variety of bottle sizes. The built-in bottle filler is a beneficial feature for students and professionals alike, promoting hydration while simultaneously discouraging the use of disposable bottles.

Moreover, these models are engineered for durability, constructed from high-quality materials that withstand the rigors of daily use. The sleek stainless steel finish not only contributes to a modern aesthetic but also resists corrosion and is easier to clean, ensuring the units maintain their appearance over time.

In terms of size, the Elkay EDFP217RAC and EDFP217C are compact enough to fit in various environments, such as schools, universities, parks, and office buildings, making them versatile additions to any setting.

Ultimately, the Elkay EDFP217RAC and EDFP217C are perfect for those who value sustainability, convenience, and design in their drinking water solutions, reflecting a growing trend towards eco-friendly products in contemporary society. The combination of advanced features, technologies, and practical design makes these models ideal for modern hydration needs.