Dixon 13091-0500 Specifications, Folded sheet metal, fore and aft, Electric clutch, Front, Rear

Page 11

SPECIFICATIONS

	SPECIFICATIONS
		7000 Series
CHASSIS:	11 GA - rectangular tube
BODY:	Folded sheet metal.
SEAT:	Designed for operator comfort with padded back and arm rests. Seat is adjustable
	fore and aft.
MOWER DECK:	2 Decks are available. Both decks are made of 10 GA fabricated welded
	construction with 7 GA reinforcement plate. 3 blades combine for either a 52" or
	60" cut width. Cut height approximately 1.5" to 5" via 7 position lift handle.
BLADE DRIVE:	Electric clutch
DRIVE SYSTEM:	Each rear wheel is independently driven by a HydroGear BDU-10L Series 70
	hydrostatic transmission. The hydrostatic transmissions, in turn, power a fully
	enclosed HydroGear gearbox.
ENGINE:	25HP Kohler Command, 4-Cycle, V-Configuration, Overhead Valve, Air-
	Cooled, Gasoline, Vertical Shaft, Aluminum Head, and Crankcase with Cast
	Iron Liners, Full Pressure Lubrication/Full Flow Filter, Pulse-type Fuel Pump,
	Fixed Jet Carburetor w/Smart-Choke, Electronic Ignition, In-Line Fuel Filter,
	Dual Element Air Cleaner.
STARTING SYSTEM:	Electric by key switch operation with safety interlocks on parking brake and
	blade drive clutch.
TIRES:	Front	13-5.00x6
	Rear	23-9.50x12
RECOMMENDED	Front	12 lbs.
TIRE PRESSURE:	Rear	12 lbs.
CAPACITIES:	Fuel - 11 gallons (approx)
	Hydrostat oil tank - 3 quart with in-line 40 micron filter
	Hydrostat oil recommendation, refer to page 36
	Engine - 2 qts. SAE 10W30 (with filter)
DIMENSIONS:	Width	61"(52" Deck), 69-1/2"(60" Deck)
	Height	43"
	Length	81" (52” Deck), 81” (60” Deck)
	Weight	915 lbs.(48" Deck), 916 lbs.(60" Deck)
NOTE:	Additional information provided in service instructions under the individual
	component.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Page 11

Image 11

Contents 2001 Operators Manual7000 SERIES ZTR MOWERS IMPORTANT - READ CAREFULLY SPECIFICATIONS INDEXSAFETY WARRANTY POLICYThe most common causes of injury to the operator or bystander SAFETYRIDING LAWNMOWERS, IF IMPROPERLY OPERATED CAN CAUSE SERIOUS INJURY OR DEATHWhen you see this symbol BE ALERT to the potential for injury DangerSafety Alert Symbol Follow recommended safety precautions and safe operating practicesand throwing objects GENERAL OPERATIONFailure to observe the following safety instructions could result in This cutting mower is capable of amputating hands & feetAll slopes require extra caution SLOPE OPERATIONwhich can result in severe injury or death presence of children NEVER assume children will stay where they were last seenCHILDREN Tragic accidents can occur if the operator is not alert to theSERVICE AND LIMITATIONS DIXON LIMITED WARRANTY POLICY - COMMERCIAL MODELSLABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS DIXON ZTR MOWERS ARE WARRANTED AGAINST DEFECTS IN MATERIALSFolded sheet metal SPECIFICATIONSDual Element Air Cleaner WeightSEAT ADJUSTMENT INSTRUCTIONS 1. Grasp seat slide adjuster and move it into adjustment position2. Slide seat forward or backward 3. Release seat slide adjuster ModelSteering Control Levers Choke Parking Brake Lever CONTROLSBlade Clutch Switch Ignition Key Throttle Cut Height Adjustment Lever Cut Height Stop PinEach lever controls one side of the mower PARKING BRAKEEngage parking brake before starting engine Allows the mower to turn on its own axis zero turning radiusBRAKING TO GO FORWARDTO GO BACKWARD TURNINGLocated to the right and front of operator To engage blades Pull up on the switch To disengage blades Push downControls the cutting height Seven positions of adjustment Located on control panel, on operators rightBEFORE OPERATING MOWER OPERATION INSTRUCTIONS1. The mower blades must be disengaged before the engine will start TESTING OF SAFETY INTERLOCK SYSTEMSBLADE DRIVE SWITCH TEST Electric Clutch Do not operate mower if safety switches are not operating properlySTARTING INSTRUCTIONS Cold Engine STARTING INSTRUCTIONS Always turn engine off when leaving mowerCorrect mowing height can reduce weeds and disease by 50% to 80% Be sure that deflector is properly installed on the discharge chuteGRASS HEIGHT SUGGESTIONS 5. Maintain Sharp Blades Throughout The Cutting SeasonTO FREE WHEEL MACHINE UNLOCK TRANSMISSION MAINTENANCE SCHEDULE CARE AND MAINTENANCEENGINE BATTERYBattery electrolyte is a poisonous and corrosive sulfuric acid solution. Avoid spilling on skin, eyes and clothingV-BELTS MOWER BLADESDirt or water in oil can ruin the hydrostatic transmissions LUBRICATIONCHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION PARKING BRAKE ADJUSTMENT HYDROSTATIC TRANSMISSIONS HYDROSTAT DRIVE BELT REPLACEMENT PROCEDURESTEERING CONTROL ADJUSTMENTS STEERING CONTROL ADJUSTMENTS continued LEVELING THE DECK PROCEDURE FOR RAISING AND LOWERING THE DECK FOR SERVICING of the way Cut Height Adjustment Pin Cut Height Adjustment Lever Locking PinDeck Latch Foot Deck Center Deck Spindle Deck Lift Bolt Rear Deck Mounting Latch Front Caster Wheels positioned outKOHLER AIR AND OIL FILTER PART NUMBERS STANDARD SERVICE PARTS LISTMODEL ZTR add oil TROUBLESHOOTINGcheck ventPut in lock position see pg Check spark plug or condition andCheck and re-gap Add oilPage Page DATE ENGINE TUNED OWNER INFORMATIONDATE PURCHASED MOWER MODEL NUMBER MOWER SERIAL NUMBER PURCHASED FROM DATE OIL CHANGEDPO Box Dixon and ZTR are registered trademarks of Dixon Industries, IncDIXON INDUSTRIES, INC a BLOUNT International Inc. Co