Body Removal, Adjustment of Mower Deck Drive Belt

BODY REMOVAL

1.The 3301 has a 2-piece polyethylene body. The upper body can be folded forward to expose the transaxle. In some cases, it may be necessary to remove t he upper body to service the transaxle.

2.To remove the upper body, remove two bolts P/N 3093 from the front of upper body hinge located on the brake shaft P/N 9283. Disconnect seat switch P/N 4761 at plug-in.

3.Reverse above procedure to reinstall.

ADJUSTMENT OF MOWER DECK DRIVE BELT

1.The mower deck drive belt is tensioned by a spring loaded engagement idler quadrant.

2.This system is designed to maintain the proper belt tension at all times.

3.Belt tension can be adjusted by moving the engaging rod P/N 7013 into the outside hole of engagement handle P/N 7020.

4.After belt tension is adjusted, check to assure that the mower blade will not turn freely when the engaging rod is in the "OFF" position.

5.If the mower blade turns freely, adjust the blade by loosening nut P/N 3205 at the end of the brake rod P/N 2988.

6.After adjustment is achieved, perform the safety checks listed below.

REMOVING THE MOWER BLADE

Secure blade P/N 2483 from turning. Remove blade bolt from center, P/N 3268 and blade washer P/N 6260, then blade P/N 2483. To reinstall, reverse above procedure. Tighten blade bolt to 60 ft. lbs. of torque.

WARNING:	Sharp edges on blade can cause injury!
	Caution should be exercised when service is required on blade.

REMOVING MOWER DECK

1.Loosen the belt keepers P/N's 7026 & 7027, located under the engine, by loosening the mounting bolts, allowing the deck drive belt to come free of the rear pulley.

2.Disconnect the wiring loom at the deck safety switch P/N 4242.

3.Remove the two clevis pins P/N 3072 from the two rear L -rods P/N 1355 and slide from slots.

4. Remove clevis pins P/N 3072, and L -rod attached to lift handle, and slide from slot.

5. Remove clevis pin P/N 3072 from front deck hanger shaft P/N 1332, located at front of mower deck on slide plates welded at battery box and remove.

6. Lift front of mower chassis and roll free of the deck.

7. To install, reverse the above procedure.

Page 2 of 8

3301 specifications

Dixon 3301 is an advanced piece of surveying and geospatial technology that's gaining recognition in various industries, including engineering, construction, and environmental management. This high-performance total station combines cutting-edge technologies with user-friendly features, making it a preferred choice for professionals requiring precise measurements and detailed mapping capabilities.

One of the standout features of the Dixon 3301 is its impressive accuracy. It boasts a measurement precision that can reach down to millimeters, making it ideal for tasks such as construction layout and topographic surveys, where precision is paramount. The instrument is equipped with advanced angular measurement technology, which ensures reliable angles and distance measurements, further enhancing its overall reliability in demanding environments.

The Dixon 3301 utilizes a state-of-the-art laser rangefinder, allowing for contactless distance measurements over large areas. This technology not only speeds up the surveying process but also reduces the potential for human error. The device can measure distances up to several kilometers with remarkable accuracy, making it suitable for both urban and rural surveying applications.

Another key characteristic of the Dixon 3301 is its rugged design. Built to withstand harsh weather conditions, the total station is often rated with an IP67 protection class, meaning it is dust-tight and can withstand immersion in water up to 1 meter for 30 minutes. This durability ensures that the instrument can be used in various outdoor environments without the risk of damage or malfunction.

In terms of usability, the Dixon 3301 features an intuitive interface that simplifies operations and enhances productivity. Its large, bright display screen is easy to read, even in bright sunlight, and the device is equipped with a battery that offers extended operation time, ensuring that professionals can work uninterrupted throughout the day.

Additionally, the Dixon 3301 supports various data transmission options, including Bluetooth and USB connectivity. This allows for seamless integration with other devices like tablets and computers, facilitating smooth data transfer and real-time monitoring. The total station also comes with advanced software that enhances data processing capabilities, enabling users to analyze and visualize data efficiently.

In summary, the Dixon 3301 represents a significant advancement in surveying technology. With its high accuracy, robust design, user-friendly interface, and advanced connectivity options, it stands out as a powerful tool for surveying professionals looking to optimize their workflow and improve measurement accuracy. Its versatility makes it suitable for a range of applications, ensuring it meets the diverse needs of the modern surveying industry.