Dekko 52H Mowing and Floating Deck Instructions, Changing the Height of Cut, Removing the Blades

Page 14

Heavy Duty Power Equipment

Mowing and Floating Deck Instructions

36B, 36BX, 36H, 36HX, 52H, 52HX

Changing the Height of Cut

Your DEK mower is equipped with an easily adjustable floating deck which can be adjusted for cut heights of 1½” to 4½” in ½” increments.

Figure 6

How to Change the Cut Height

1.Hold one side of the deck by the black handle provided (Figure 7).

3.Raise or lower the deck until the hole in the height adjust bar (Figure 9A) aligns with the de- sired cut height hole on the height adjust bracket (Figure 9B).

4.Replace the height adjust pins into the desired cut height holes. All 4 height adjust pins must be set to the same desired cut height position.

Figure 9A

5.Repeat the same adjust- ment process with the two height adjust pins / brackets on the other side of the mower deck.

Figure 7

2.Using your other hand, remove the retaining clip and pin from the two brackets on that side of the mower. (Figure 8).

Figure 8

Removing the Blades

Figure 9B

CAUTION

Beware of the cutting edges on the blades. The rotation of one blade may cause the other blade(s) to rotate. Always wear work gloves when handling blades.

1.Park the mower and level ground and block the rear wheels to prevent accidental rollback.

2.Raise the front end of the mower using a jack stand.

3.Using two 15/16” box end wrenches. Use one wrench to loosen nut “A” while holding bolt “C” with the other wrench. (Figure 10)

4.Slide the blade bolt down through the mower deck and out.

5.To reinstall, reinsert the blade bolt through the cutting deck.

6.Install the blade spacers that were removed,

back onto the blade bolt

A

followed by the nut and

 

tighten. (Figure 10)

 

IMPORTANT: The

 

amount of spacers

 

should always be the

 

same on each blade

 

bolt. Never put the

 

spacers below the

 

blade.

C

 

Figure 10

 

DEK® is exclusively distributed by GXi International, LLC

Rev: 8/2008

14 of 21

Image 14
Contents Heavy Duty Power Equipment Lawn Mowers & Accessories Generators, Welder Generators & AccessoriesPressure Washers & Accessories Chipper ShredderTable of Contents Safety Information and Warnings Before Using Your DEK Lawn MowerProduct Specifications Safety Decals & Product SpecificationsSafety Decal Identification Control Panel Identification Gear Drive Models Hydro Drive ModelsAssembly Instructions Front Wheel Assembly Assembly Instructions Gap in full forward position Plates36B, 36BX, 36H, 36HX, 52H, 52HX For 36 Models Above 36 Honda Mower Throttle and Choke Connection Assembly Instructions Throttle and Choke Cable ConnectionsFuel tank connections Operating Instructions Operating the Mower hydro drive models Mowing Grass with Your DEK Lawn MowerRemoving the Blades Mowing and Floating Deck InstructionsChanging the Height of Cut Fuel General MaintenanceCleaning the Mower Engine Oil Air Filter Tire PressureLubricate after every 50 hours of usage Lubrication PointsLubrication point locations Engine to Blade Belt Adjustment Service AdjustmentsDrive Belt and Brake Adjustment, 36B and BX Models Blade to Blade Belt AdjustmentBelt Drive System Engine to Transmission Belt AdjustmentSafety System Adjustments See Figure Hydro Drive SystemTroubleshooting Problem Possible Causes SolutionTroubleshooting Limited Warranty & Service 36B, 36BX, 36H, 36HX, 52H, 52HX

36B, 36H, 52H, 36BX, 36HX specifications

The Dekko series, including models 36HX, 36BX, 52H, 36H, and 36B, represents a significant innovation in the realm of high-performance machinery. These models are designed specifically to enhance productivity while ensuring user-friendly operation, making them suitable for a wide range of industrial applications.

One of the key features of the Dekko 36HX is its robust design combined with advanced automation technologies. This model is equipped with high torque motors that provide exceptional power and efficiency. The 36BX model complements this with its unique ability to handle a variety of materials, making it a versatile choice for any workshop or manufacturing floor. Both models prioritize safety, incorporating automatic shut-off systems that protect operators during sudden power fluctuations.

The Dekko 52H stands out with its larger capacity, making it ideal for heavy-duty applications. Its precision engineering allows for high-speed operations while maintaining accuracy, a critical requirement in industries where minute tolerances are crucial. Additionally, it features an intuitive digital interface that assists operators in monitoring performance metrics and operational parameters in real time.

Conversely, the Dekko 36H and 36B models focus on compactness and space efficiency without sacrificing performance. These models are particularly suited for smaller operations or workshops where floor space is limited. Despite their size, they incorporate powerful motors and are engineered for durability, ensuring long-lasting service even under demanding conditions.

All models in the Dekko series employ innovative cooling technologies that prevent overheating during extended operations, thereby prolonging the lifespan of the equipment. Furthermore, they are built with eco-friendly materials and energy-efficient designs, aligning with modern sustainability goals.

In terms of user experience, the Dekko series offers easy maintenance features that reduce downtime. Key components are easily accessible, allowing operators to conduct regular checks and replacements with minimal effort.

In conclusion, the Dekko 36HX, 36BX, 52H, 36H, and 36B embody a perfect blend of strength, precision, and technology. Their unique features and characteristics cater to diverse industrial needs, making them a valuable investment for any business aiming to enhance operational efficiency and productivity. With their commitment to innovation and sustainability, the Dekko series is positioned to lead the market for high-performance machinery in the coming years.