Bush Hog Home Series manual Deck Belt Adjustment, Deck Belt Replacement, Deck Belt Diagram

Page 20

LEVELING THE DECK AND SETTING THE COUNTERBALANCE SPRING TENSION

CAUTON

STOP THE ENGINE, SET PARKING BRAKE, REMOVE IGNITION KEY AND SPARK PLUG WIRES FOR SAFETY.

1.Set all tire pressures to the correct specifications.

2.Rest machine on a level slab of concrete.

3.Depress the deck lift pedal to raise the deck to the full lift height position and move the height adjust pin to the 4.5” position.

4.Take all the force off the deck lift spring by loosening the nut at the front of the spring.

5.Place a level on the deck, from front to rear. If the level is too short to reach all the way from front to rear, lay a straight edge on the deck first, then place the level on the straight edge.

6.Lay a .12” spacer beneath the front level. this will automatically set the rear of the deck higher than the front.

7.Adjust the bolts in the slot to raise the rear of the deck (Shown below) until the level’s bubble is cen- tered. Repeat for the other side.

8.Check to verify the deck is leveled side-to-side. To do this, lay a 2” x 4” x 30” piece of wood under each side of the deck and lower the deck to rest freely on the top of these boards. Inspect the (3) lift hangers to see if tension is on each of them. If any of the hangers appear slack, adjust the bolt in the slot to remove the slack.

9.Raise the deck up to the transport position and pin in the desired height position.

10.Remove the 2” x 4”s from under the deck.

11.Tighten the counterbalance spring nuts until spring is to the following length:

 

Bolt In Slot

 

Level on

 

Mower Deck

 

.12” Spacer At Front End

Height

Upper

Adjustment Pin

Chain Fastener

 

Deck

 

Lift Pedal

 

Deck

Deck Shield

Deck Lift Spring

36” & 42” Deck- Spring length of 16” for 3” cut- ting height. For lower cutting heights loosen springs at 1/4” intervals until stop hits adjusting pin in correct height location. If deck floats, loosen springs at 1/4” intervals until deck stops floating.(Measure from back of flatwasher to back of flatwasher)

DECK BELT ADJUSTMENT

Belt adjustment should be checked every (50) hours of operation to get maximum life and cutting perfor- mance. Belt tension is adjusted by increasing or decreasing the length of the spring on the movable idler by adjusting the eye bolt length (Shown below). For correct belt tension, adjust the spring length to 7” for the 36” and 7-1/2” for the 42” deck.

DECK BELT REPLACEMENT

(NOTE: Use only genuine Bush Hog replacement parts)

1.Remove the R.H. and L.H. deck shield assem- blies and remove the foot platform.

2.Relieve the spring tension by loosening the two 3/8” hex nuts on the spring adjustment eye bolt.

3.Remove the old belt.

4.Install the new belt being sure the belt is properly routed and positioned in all sheave grooves.

5.Adjust tension on the belt by adjusting the length of the spring on the idler (See Deck Belt Adjustment section).

6.Replace the deck shield assemblies and foot platform.

DECK BELT DIAGRAM

Spring Length - 36” Deck - 7”, 42” Deck - 7-1/2”

(Measured From

Of Hooks)

Eye Bolt Adjustment

Spring Loaded Idler

WARNING

TO AVOID SERIOUS BURN INJURIES:

•ALLOW ENGINE, OIL AND HYDRAULIC FLU- IDS TO COOL BEFORE SERVICING TRANSMIS- SION OR ENGINE SYSTEM

CAUTION

TO AVOID CLEANING SOLVENT FIRES:

•AVOID USING FLAMMABLE SOLVENTS.

•AVOID AREAS WITH IGNITION SOURCES WHEN USING FLAMMABLE SOLVENTS.

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Bush HOG Congratulations Table of Contents Retail CUSTOMER’S Responsibility Under the Bush HOG WarrantyThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Home Series Zero Turn Riding MowerSafety Alert Symbol Your Safety is InvolvedImportant Safety Precautions Accident Patterns to AvoidSafety Never Carry PassengersTowing Slope OperationEMPLOYERS, Employees and Operations This Act SeeksOsha Regulations Child Labor Under 16 Years OldDescription SectionIntroduction Tractor Specifications Deck SpecificationsControls Operator Interlock SystemGeneral Safety PRE-OPERATION ChecklistSection Operation Do not mix oil with gasolineCauton Cutting Height Adjustment DecalOperation Transporting ANTI-SCALP RollerMowing Recommendations Hr break-in Grease front wheels every 50 hours Section MaintenanceMaintenance Schedule Engine Tighten retaining bolt to 76 ft./lbsDrive Adjustments Motion Control Lever AdjustmentMotion Control Steering Adjustment Stop the Engine Before Making AdjustmentsDeck Belt Diagram Deck Belt AdjustmentDeck Belt Replacement START-UP Maintenance START-UP ProcedureHydrostatic Maintenance Parking Brake AdjustmentParking Brake Cable Replacement / Installation Pump Drive Belt Tension AdjustmentTroubleshooting Check List Mounting the Seat Section IV AssemblyMounting the Control Levers Page Safety Decals 50029501 Torque Specifications Recommended Torque in Foot Pounds Newton MetersHome Series Zero Turn Riding Mowers Slope Angle Guide Fold Along Appropriate Line

Home Series specifications

Bush Hog is a name synonymous with robust and reliable land management equipment, and their Home Series is specifically designed to bring the power and durability of professional-grade machinery to the everyday user. Whether you're a homeowner with a large property, a small farm owner, or just someone who takes pride in maintaining their landscape, the Bush Hog Home Series provides versatile solutions for a variety of tasks.

One of the standout features of the Bush Hog Home Series is its exceptional cutting performance. These mowers are engineered to handle tough grass and thick underbrush, ensuring a clean and precise cut every time. The Home Series is equipped with heavy-duty, offset decks that provide better maneuverability and efficiency, allowing users to navigate through tight spaces and uneven terrain with ease.

Durability is a hallmark of the Bush Hog brand, and the Home Series is no exception. With a rugged construction that includes a robust steel frame and reinforced components, these machines are built to withstand the rigors of regular use. Additionally, the Home Series mowers utilize high-performance blades that can easily tackle dense vegetation, ensuring longevity and reducing the need for frequent replacements.

In terms of technology, the Bush Hog Home Series incorporates advanced features focused on user comfort and convenience. With ergonomic controls and adjustable seating, operators can enjoy a more comfortable mowing experience, reducing fatigue during extended periods of use. Many models also include electric start options, simplifying the startup process and making it more accessible for users of all skill levels.

Safety is also a priority in the Home Series lineup. These mowers come equipped with essential safety features such as automatic blade brakes and rollover protection systems, providing peace of mind for operators. Furthermore, the intuitive layout of controls ensures that users can operate the machine safely and effectively without the need for extensive training.

Lastly, the Bush Hog Home Series emphasizes ease of maintenance. Designed with user-friendliness in mind, these machines feature easily accessible components, allowing for straightforward maintenance routines. Regular upkeep is simplified, contributing to the overall longevity and performance of the equipment.

In conclusion, the Bush Hog Home Series combines powerful cutting performance, durability, user-friendly technologies, and safety features, making it an ideal choice for homeowners and small farm operators alike. With a reputation built on quality and reliability, Bush Hog continues to deliver exceptional land management solutions with their Home Series lineup.
Top Page Image Contents