SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUG
To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This equipment must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized connections will fit together only one way. Make sure that the receptacle end of the extension cord has large and small blade slot widths. If the plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain a suitable extension cord. If the extension cord does not fit fully into the outlet, contact a qualified electrician to install the proper outlet. Do not change the tool plug or extension cord in any way.
BEFORE OPERATING
•SECURING POWER SUPPLY CORD - Secure the extension cord in the tool's
SWITCH
NOTE: The switch will not operate if the release button, shown in Figure 1, is depressed. To turn the tool ON, slide the switch forward, as shown in Figure 1. To turn tool OFF, slide switch to the rear.
OPERATION
USE AS A BLOWER: ALWAYS WEAR SAFETY GLASSES, WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY.
•BLOWER MODE
Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble blow tube as shown in Figure 2. (This only needs to be done the first time you assemble the unit.)
WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop rotating before disassembly.
Attach the blower tube assembly (The assembly includes the blower tubes, the fan chamber and the blower air speed control mechanism) to the front of the tool, as shown in Figure 3 by inserting point A into the matching recess marked point B, also shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4.
NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position.
Hold the end of the blower tube approximately 7 inches (180mm) above the ground and turn the tool ON. Using a sweeping motion, from side to side, advance slowly keeping the accumulated debris (leaves,grass clippings etc.) in front of you, as shown in Figure 5.
•BLOWER AIR SPEED CONTROL
Your Blower has a variable air speed feature that allows you to select the air speed that best fits your needs. To adjust the air speed, simply slide the collar. This will allow movement over the full range of 1 3/4 in.(44.5mm).With the slide collar in the "A" position, as shown in Figure 6, the maximum blower speed will be 200 mph (320 kph). When pushed forward to position "C" ( as far from the tool housing as possible; about 1 3/4 in.{44.5mm}) the speed will be approximately 140 mph (225 kph). Position "B" (midway between the two) permits infinite adjustment between positions "A" and "C". A little practice will help you determine what is the best speed for your application.
•REMOVING THE BLOWER TUBE ASSEMBLY
Switch off the unit and unplug from the outlet.
To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube does not fall to the ground.
NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position.
TROUBLESHOOTING
Problem | Possible Cause | Possible Solution |
• Unit will not start. | • Cord not plugged in. | • Plug tool into a working outlet. |
| • Circuit fuse is blown. | • Replace circuit fuse. (If the product |
repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)
•Circuit breaker is tripped. • Reset circuit breaker. (If the product repeatedly causes the circuit breaker to trip, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)
• Cord or switch is | • Have cord or switch replaced at Black |
damaged. | & Decker Service Center or Authorized |
| Servicer |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
MAINTENANCE
•CLEANING AND STORAGE
TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.)
CAUTION: DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN.
Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country specific warranty information contained in the packaging, call the local company or see the website for warranty information.
Imported by | See ‘Tools- | |
Electric’ | ||
Black & Decker (U.S.) Inc., | ||
– Yellow Pages – | ||
701 E. Joppa Rd. | ||
for Service & | ||
Towson, MD 21286 U.S.A. | ||
Sales | ||
|
SOUFFLEUR
MODE D’EMPLOI
N° de catalogue : BL1200
Merci d’avoir choisi Black & Decker!
Consulter le site Web
www.BlackandDecker.com/NewOwner pour enregistrer votre nouveau produit.
ÀLIRE AVANT DE RETOURNER CE PRODUIT POUR QUELQUE RAISON QUE CE SOIT :
Si des questions ou des problèmes surgissent après l’achat d’un produit Black & Decker,
consulter le site Web
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pour obtenir des réponses instantanément 24 heures par jour.
Si la réponse est introuvable ou en l’absence d’accès à Internet, composer le
Prière d’avoir le numéro de catalogue sous la main lors de l’appel.
CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.
AVERTISSEMENT : AVERTISSEMENTS DE SÉCURITÉ ET DIRECTIVES DE PREMIÈRE IMPORTANCE
AFIN DE RÉDUIRE LES RISQUES DE BLESSURES :
•Avant toute utilisation, s’assurer que tous ceux qui se servent de l’outil lisent et comprennent toutes les mesures de sécurité et tout autre renseignement contenus dans le présent guide.
•Conserver ces mesures et les relire fréquemment avant d’utiliser l’outil ou d’en expliquer le fonctionnement à d’autres personnes.
AVERTISSEMENT : Afin de réduire les risques d’incendie, de secousses électriques ou de blessures lorsqu’on utilise des outils électriques, il faut toujours respecter les mesures de sécurité suivantes.
AVERTISSEMENT : Le produit génère de la poussière qui peut renfermer des produits chimiques. Selon l’état de la Californie, ces produits chimiques peuvent causer le cancer ainsi que des malformations congénitales, et ils présentent d’autres dangers au système reproductif humain. Voici des exemples de tels produits chimiques :
•les composés d’engrais;
•les composés d’insecticides, d’herbicides et de pesticides;
•l’arsenic et le chrome provenant de bois traité.
Afin de minimiser les risques, porter de l’équipement de sécurité approuvé comme des masques antipoussières spécialement conçu pour filtrer les particules microscopiques.
AVERTISSEMENT : Le produit renferme des produits chimiques, dont du plomb. Selon l’état de la Californie, ce produit chimique peut causer le cancer ainsi que des malformations congénitales, et il présente d’autres dangers au système reproductif humain. Se laver les mains après l’utilisation.
MISE EN GARDE : Porter un dispositif approprié de protection de l’ouïe lors de l’utilisation du produit. Dans certaines conditions et durées d’utilisation, le produit peut émettre un niveau de bruit provoquant la perte de l’ouïe.
LIRE TOUTES LES DIRECTIVES AVANT D’UTILISER L’OUTIL.
LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS
Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les symboles
DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou des graves blessures.
AVERTISSEMENT : Indique une situation potentiellement
dangereuse qui, si elle n’est pas évitée, pourrait causer la mort ou de graves blessures.
MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait causer des blessures mineures ou modérées.
MISE EN GARDE : Utilisé sans le symbole d’alerte à la sécurité, indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en des dommages à la propriété.
AVERTISSEMENTS ET DIRECTIVES DE SÉCURITÉ GÉNÉRALES POUR TOUS LES OUTILS.
•LIRE et respecter toutes les mesures de sécurité.
•NE PAS porter l’entrée ou la sortie du tube de souffleur à proximité des yeux ou des oreilles lorsque l’outil fonctionne.
•L’OUTIL EST MUNI D’UNE DOUBLE ISOLATION. Utiliser seulement des pièces de rechange identiques. Voir les directives sur l’entretien des outils à double isolation.
•RANGER LES OUTILS NON UTILISÉS dans un endroit sec, situé en hauteur ou fermé à clé, hors de portée des enfants.
•NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder son équilibre en tout temps.
•BIEN ENTRETENIR L’OUTIL. Garder le ventilateur propre afin d’optimiser et de sécuriser le rendement. Suivre les directives d’entretien.