American Standard 2901E SERIES installation instructions General Installation Information

SAVONA ELITE™

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2901E SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

		1810mm		19mm
		(71-1/4)
				(3/4)
	905mm	IN-LINE HEATER
				TYP.
	(35-5/8)	REMOVABLE
		BLANK
1105mm	552mm			PUMP
	(21-3/4)			OUTLINE OF
(43-1/2)
		C/L		1772mm X
				1067mm
				(69-3/4 X 42)
				CUTOUT
		178mm
		(7)
305mm	140mm
(12)
	(5-1/2)
				ON/OFF
C/L OF 1-1/2 O.D.		229mm X 305mm		SWITCH
DRAIN OUTLET
		(9 X 12) FLOOR
	● RECOMMENDED
	FITTING LOCATION	CUTOUT	PROVIDE ACCESS
	64 X 279mm (2-1/2 X 11)
			TO PUMP FOR SERVICE
	C/L OF OVERFLOW		ON ALL INSTALLATIONS
			■ LEVELING STRINGER
	38mm	89mm
				NOT FOR SUPPORT
51mm	(1-1/2)
		(3-1/2)
(2)
				559mm
				(22)
				508mm
				(20)
	INTEGRAL
	FEET
	44 mm			ROUGH
	(1-3/4)
				FLOOR
	89 mm
	(3-1/2)
	1-1/2 O.D. TAILPIECE	1-1/2 N.P.T.M.
		THREADS

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

•Flex-Jet Pulse Jet Kit*

•Flex-Jet Soft Jet Kit*

•E-Z-Install Heater*

•Tile Bead Kit*

List of Required Components (not included):

• Drain* • Bath Filler*

* see your Home Depot Retailer

GENERAL SPECIFICATIONS FOR 2901E WHIRLPOOL

INSTALLED SIZE		71-1/4 x 43-1/2 x 22 In.(1810 x 1105 x 559mm)
WEIGHT					152 Lbs. (68 Kg.)
WEIGHT w/WATER					936 Lbs. (421 Kg.)
GAL. TO OVERFLOW					94 Gal. (356 L)
WHIRLPOOL MIN. OPERATING VOL.					86 Gal.(326 L)
BATHING WELL AT SUMP				44 x 28 In. (1118 x 711mm)
BATHING WELL AT RIM			67-1/2 x 33 In. (1715 x 838mm)
WATER DEPTH TO OVERFLOW					16-1/4 In. (413mm)
FLOOR LOADING			43 Lbs./Sq.Ft. (211 Kgs./Sq.m)
(PROJECTED AREA)
PTS.			27.8
CUBE (FT3)						61.5
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP					2.1 HP, 14.4 AMPS, 120V.

GENERAL INSTALLATION INFORMATION

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	20 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752867-100 Rev. DAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.