American Standard 2711.028WC General Specifications for 2711 Whirlpool, Safe-T, Removable Blank

72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm) 133 Lbs. (60 Kg.)

950 Lbs. (432 Kg.)

95 Gal. (360 L)

ELLISSE™ 6' x 48"

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

305mm

(12)

1219mm

(48)

		1829mm
		(72)
	927mm		OUTLINE OF CUTOUT		102mm
			1791 X 1181
(36-1/2)			(70-1/2 X 46-1/2)	(4)

305mm

(12)

	C/L OF
	DRAIN
229mm x 356mm
(9 x 14) FLOOR	PUMP	1219mm
CUTOUT		(48)

		1829mm
		(72)
	927mm		OUTLINE OF CUTOUT
			1791 X 1181
(36-1/2)			(70-1/2 X 46-1/2)

229mm x 356mm (9 x 14) FLOOR CUTOUT

102mm

(4)

C/L OF

DRAIN

RECOMMENDED FITTING LOCATION 64X279mm 2-1/2 X 11)

51mm

(2)

INTEGRAL

FEET

SUPPORT

GRAB BAR			PROVIDE ACCESS
FITTING AREA	OPTIONAL
		TO PUMP FOR SERVICE
	DECK FITTING
		ON ALL INSTALLATIONS
	AREA
			LEVELING STRINGER
		SAFE-T-
		HEATER	(NOT FOR SUPPORT)
		REMOVABLE		C/L OF
		BLANK
				OVERFLOW
			105mm	546mm
				(21-1/2)
			(4-1/8)
			ROUGH	495mm
			FLOOR	(19-1/2)
1-1/2 N.P.T.M. THREADS
1-1/2 O.D.TAILPIECE		64mm		121mm
				(4-3/4)
		(2-1/2)

RECOMMENDED	GRAB BAR
FITTING	FITTING AREA	OPTIONAL
LOCATION		DECK FITTING
64X279mm		AREA
2-1/2 X 11)					LEVELING STRINGER
					(NOT FOR SUPPORT)
51mm									C/L OF
(2)
									OVERFLOW
INTEGRAL				105mm					546mm
								(21-1/2)
			(4-1/8)
FEET
SUPPORT				ROUGH			495mm
				FLOOR		(19-1/2)
	1-1/2 N.P.T.M. THREADS						121mm
	1-1/2 O.D.TAILPIECE		64mm
			(2-1/2)			(4-3/4)

GENERAL SPECIFICATIONS FOR 2711 WHIRLPOOL

INSTALLED SIZE		72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
WEIGHT				148 Lbs. (67 Kg.)
WEIGHT w/WATER				965 Lbs. (434 Kg.)
GAL. TO OVERFLOW				95 Gal. (360 L)
WHIRLPOOL MIN. OPERATING VOL.				74 Gal. (280 L)
BATHING WELL AT SUMP				43 x 28 In. (1092 x 711mm)
BATHING WELL AT RIM				68 x 38 In. (1727 x 965mm)
WATER DEPTH TO OVERFLOW				14-5/8 In. (371mm)
FLOOR LOADING			40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
(PROJECTED AREA)
PTS.					30.3
CUBE (FT3)						60.8
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM II PUMP				2.1 HP, 15.6 AMPS ,120V.

GENERAL SPECIFICATIONS FOR 7211 BATHING POOL

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP			43 x 28 In. (1092 x 711mm)
BATHING WELL AT RIM		68 x 38 In. (1727 x 965 mm)
WATER DEPTH TO OVERFLOW				14-5/8 In. (371mm)
FLOOR LOADING	40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
(PROJECTED AREA)
PTS.					30.3
CUBE (FT3)						60.8

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. OPTIONAL GRAB BAR KIT AVAILABLE AND MUST BE ORDERED SEPARATELY.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING. MOUNTING HOLES DRILLED BY INSTALLER.

SUPPLY PIPING NOT INCLUDED.

ON SYSTEM II VARIATION: SYSTEM CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL A MINIMUM OF (152MM) 6" ABOVE ROUGH FLOOR.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

	H48
© 2008 AS America Inc.		Revised 2/08