Husqvarna 340, 345, 346XP,350, 351, 353 manual Ignition module and flywheel refitting

Page 26

Repair instructions

Ignition module and flywheel – refitting

Place the flywheel on the crankshaft. Turn the flywheel so that the key lines up with the keyway in the shaft.

Fit the washer and nut on the shaft and tighten to a torque of 25-30 Nm.

0,3 mm

To refit the ignition module proceed as follows:

Turn the flywheel so that the magnets are in line with the ignition module. Fit the ignition module with the plastic feeler gauge (502 51 34-01) held in position at the same time, without tightening the bolts. Connect the black earth lead to the front screw on the ignition module. Adjust the gap between the ignition module and magnet to 0.3 +/-

0.1mm. The gap must be measured at either of the two lowest pegs on the ignition module. Tighten the bolts to 4.5–6 Nm. Connect the blue lead to the ignition module.

Then refit:

•cable guide and press the leads into position

•HT lead

•starter assembly, tighten to a torque of 2.5–3.5 Nm

•cylinder cover

English – 25

Image 26

Contents 340 345 346XP 350 351 Workshop manual Husqvarna 340/345/346XP/350/351/353 Contents Appendix A, Carburettor EPA modelsArrangement of the manual TroubleshootingIntroduction Construction and functionSpecial instructions Safety regulationsGeneral instructions Special tools 20 b 20 c 20 aTechnical data Rpm Construction and function CarburettorConstruction and function Idling low rpm TroubleshootingStarting High rpm Acceleration and retardationChain brake dismantling Cleaning and inspectionRepair instructions Chain brake reassembly Operating testSilencer refitting Chain catcher replacementSilencer removal RefitStop switch removal Stop switch resistance measurementStop switch refitting Choke control removalThrottle lock, throttle trigger and return spring refitting Choke control refittingThrottle lock, throttle trigger and return spring removal Hand grip heater on model 346XPG, 351G, 353G removal Generator troubleshootingSwitch troubleshooting Troubleshooting carburettor heater 346XPG, 351G, 353G Heater element and rear hand grip removal Hand grip heater on model 346XPG, 351G, 353G refittingStarter assembly removal Replacing a broken or worn starter cordReplacing a worn recoil spring Starter assembly refittingTensioning the recoil spring Model 346XP, 351 Ignition module testingIgnition module/flywheel removal Replacing the generator, model 346XP, 351 Generator refittingIgnition module and flywheel refitting Centrifugal clutch refitting Inspection and cleaningCentrifugal clutch removal Oil pump removal 346XP, 350, 351 ModelOil pump removal 340 Oil pump -refitting 346XP, 350, 351Oil pump -refitting 340 Adjustable oil pump adjustment 346XP, 350, 351 Carburettor removalCarburettor dismantling On saws with a carburettor heater 346XPG, 351G, 353GCarburettor reassembly On saws with a carburettor heater 346XPG, 351G, 353G Carburettor pressure testingCarburettor refitting Carburettor heater 346XP, 351, 353 Refitting Air intake system removal Air intake system refitting Low speed jet L Carburettor adjustmentBasic requirements Fuel tank removal Fine adjustment of idling speed TCarburettor correct adjustment High speed jet HReplacing the fuel filter Replacing the fuel hoseTank vent testing Fuel tank refittingIf replacing the cylinder Piston and cylinder removalModels 340 Decompression valve pressure testing Piston and cylinder refitting 346XP, 350, 351 Cylinder pressure testing Piston and cylinder refitting 340Crankcase and crankshaft dismantling 346XP, 351 Sealing ring replacement drive side Crankshaft bearings replacement 346XP, 351Sealing ring replacement Crankshaft complete dismantling 340, 345Take care to avoid damaging the crank- case Crankshaft bearings 340, 345, 350 replacementCrankcase and crankshaft reassembly 346XP, 351 Crankshaft complete 340, 345, 350 reassembly Thread insert Repairing damaged threadsGuide bar bolts replacement Check that Basic adjustment for EPA II carburetorsReplacement of the L-needle H-needle must not rotate114 01 2003W12

340, 345, 346XP,350, 351, 353 specifications

Husqvarna is renowned for its high-quality chainsaws, and the Husqvarna 340, 345, 346XP, 350, 351, and 353 models are no exceptions. These models have garnered a reputation among both professional and amateur users for their reliability, durability, and cutting performance.

The Husqvarna 340 is an entry-level model designed for homeowners and light-duty tasks. It features a 40cc engine that provides a good balance of power and weight, making it easy to handle during extended use. The 340 is equipped with low-vibration technology, significantly reducing operator fatigue and making it suitable for less experienced users.

The Husqvarna 345 is slightly more powerful than the 340, boasting a 45.7cc engine. This model is ideal for users who require a bit more power for medium-duty tasks. It incorporates the air injection system, which helps to separate larger debris before it reaches the air filter, prolonging the life of the filter and maintaining optimal performance.

Moving up the range, the Husqvarna 346XP is a powerful professional chainsaw tailored for demanding tasks. With a 50.2cc engine and the X-Torq engine technology, it provides high cutting performance while reducing fuel consumption and emissions. The 346XP features an adjustable oil pump that allows for precise lubrication, making it an excellent choice for commercial users.

The Husqvarna 350 shares similarities with the 346XP but is designed for users who need a well-rounded saw for various applications. Its 50.2cc engine delivers ample power, and the ergonomically designed handle provides comfort during prolonged use. The chainsaw's advanced starting system ensures easy ignition, even in challenging conditions.

The 351 is another versatile option, equipped with a 50cc engine, designed for both professional and home use. It emphasizes user comfort and ease of handling. The compact design combined with features such as an efficient air filtration system makes the 351 suitable for long hours of work.

Lastly, the Husqvarna 353 is a heavy-duty model that excels in performance and longevity. It has a 50cc engine and incorporates various safety features, including a chain brake and throttle lock, to ensure safe operation. The saw also utilizes the unique anti-vibration system, minimizing vibrations that can lead to user fatigue.

In summary, the Husqvarna 340, 345, 346XP, 350, 351, and 353 models each offer distinct features catering to a wide range of users. From homeowners tackling light tasks to professionals requiring rugged performance, these chainsaws showcase Husqvarna's commitment to quality, innovation, and user-centric design.