Husqvarna YTH2148 To Replace Headlight Bulb, Interlocks and Relays, Replacing Battery See Fig

Page 25

SERVICE AND ADJUSTMENTS

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

FIG. 29

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedures.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02778

TERMINAL ACCESS DOOR

KEPS NUT

HEX BOLT

POSITIVE (RED)

CABLE

FIG. 31

TERMINAL GUARD

NEGATIVE (BLACK)

CABLE

FIG. 30

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents YTH2148 IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Mower Unassembled PartsTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Service Notes Tractor Model NO. YTH2148 YTH2148A, Product no 57 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly Repair Parts KEY Part Description Seat AssemblyWheels & Tires DecalsEngine Mower Lift Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement 532 18 99-04 11.11.03 RD
Top Page Image Contents