Husqvarna 5524STE owner manual KEY Part Description

Page 29

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY	PART		KEY	PART
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	532 18 10-44 Spring, Traction Idler		27	532 85 10-84	Screw, Hex Head 3/8-24 x 1-3/8
2	532 18 05-22 Pulley, Idler (2-1/4)		28	532 15 54-52	Guide, Belt
3	- - -	Engine, Tecumseh, Model Number	29	532 19 22-13	Belt Cover Assembly
		LH195SP (For engine service and			(Includes Toolbox Cover)
		replacement parts, call Tecumseh	30	532 17 88-30	Cover, Toolbox
		Products at 1-800-558-5402)	31	532 40 05-24	Screw, Hex Head 1/4-20 x 1/2
4	874 78 05-20	Screw, Hex Head 5/16-18 x 1-1/4	32	532 17 92-56	Bolt, Shoulder 5/16-18
6	532 05 92-89	Washer, Flat	33	532 18 78-53	Bellcrank Shifter
7	532 16 67-85	Nut, Jam, Lock 5/16-18	34	532 19 85-80	Clevis Pin
8	532 17 53-30	Pin, Idler Pivot	35	532 40 54-85 Arm, Auger Control
9	532 17 90-92 V-Belt, Traction Drive		36	873 80 05-00	Nut, Lock 5/16-18
10	532 19 85-52	Washer, Lock 5/16	37	532 18 40-86	Bellcrank
11	532 19 85-84	Screw, Hex Head 5/16-18 x 1/2	38	532 18 71-01	Link, Speed Control
12	532 17 92-59 Impeller Arm / Pad Assembly		39	532 19 21-10	Trunnion, Pivot Bracket
13	532 08 51-79 Retainer, Hairpin		41	532 70 02-79	Hairpin, Cotter 3/32 x 1/2
14	532 17 88-28	Spring, Brake	42	532 17 90-65	Pin, Bellcrank
15	532 40 80-10V-Belt, Impeller Drive		43	532 18 40-85	Bracket, Bellcrank
16	532 15 04-06	Screw, Hex Head 3/8-16 x 1-1/4	44	817 00 06-16	Screw, Hex Head
17	532 18 48-04	Arm, Idler	45	532 18 40-74	Pivot Bracket, Impeller Idler Arm
18	874 78 05-24	Screw, Hex Head 5/16-18 x 1-1/2	46	532 18 40-84	Pan, Frame Bottom
19	532 19 85-59 Bushing, Idler Pivot		47	871 02 05-12	Screw, Hex Head 5/16-18 x 3/4
20	532 18 05-23 Pulley, Idler (2-3/4)		48	532 18 11-56	Nut, Speed 5/16-18
21	874 61 05-16	Screw, Hex Head 5/16-18 x 1	49	532 40 76-42	Frame Assembly
22	532 17 93-71 Spacer, Engine Pulley		50	532 18 80-02	Plate, Frame End
23	532 18 04-78 Pulley, Engine, Traction Drive		51	532 40 61-09	Shaft, Auger Control
24	532 17 91-57 Pulley, Engine, Impeller Drive		52	532 05 70-79	Washer, Hardened
25	532 40 00-26	Washer, Flat 3/8	55	812 00 00-02	Ring, Crescent
26	532 85 02-63	Washer, Lock, Helical 3/8	57	811 05 05-00	Washer, Lock, External Tooth 5/16
			58	532 19 85-63	Power Cord

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Image 29

Contents 5524STE Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Repair Parts Auger Housing / Impeller Assembly KEY Part Description Repair PartsControl Panel / Discharge Chute KEY Part Description Handles Repair Parts Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals 532 40 Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta