Husqvarna 395XP manual Checking chain lubrication, Lubricating the clutch drum bearing

Page 15

SAFETY INSTRUCTIONS

C Checking chain lubrication

• Check the chain lubrication each time you refuel.

Aim the tip of the saw at a light coloured surface about 20 cm away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

E Lubricating the clutch drum bearing

•Between the engine drive shaft and the clutch drum is a needle bearing that must be lubricated daily. Use the specially designed grease gun and a good quality

bearing grease.

FChecking wear on cutting equipment

Saw chain

1Check that the oil channel in the bar is not obstructed. Clean if necessary.

2 Check that the groove in the edge of the bar is clean. Clean if necessary.

3 Check that the bar tip sprocket turns freely and that the lubricating hole in the tip is not blocked. Clean and lubricate if necessary.

Check the saw chain daily for:

•Visible cracks in rivets and links.

•Whether the chain is stiff.

•Whether rivets and links are badly worn.

We recommend you compare the existing chain with a new chain to decide how badly it is worn.

When the length of the cutting teeth has worn down to only 4 mm the chain must be replaced.

min 4 mm

(0,16")

If the chain lubrication system is still not working after carrying out the above measures you should contact your service agent.

D Lubricating the bar tip sprocket

• Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

G Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASPUR (integral drive sprocket)

B RING (replaceable)

A

Regularly check the

 

degree of wear on the

B

drive sprocket. Replace if

wear is excessive.

 

Replace the drive sprocket whenever you replace the chain.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 101 89 395XPSymbols KEY to SymbolsContents Safety Instructions Chain SAW Safety EquipmentPersonal Protective Equipment Chain brake and front hand guard Throttle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilLubricating the bar tip sprocket Checking chain lubricationLubricating the clutch drum bearing Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackGeneral rules Do not let go of the handlesNever use the saw one- handed General Safety Precautions Min m10 ft General Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is WHAT? Mounting guide bar and chain AssemblyFuelmix Fuel HandlingMin 3 m FuellingWarm engine Start and StopStart Cold engineCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Adjustment of the oil pumpNeedle bearing maintenance Air filterWinter use Centrifugal cleaning Air InjectionCooling system Heated handlesMonthly maintenance Weekly maintenance Daily maintenance395XP Technical DataYour Warranty Rights Obligations Emission Control Warranty Statement2000W40
Top Page Image Contents