Husqvarna 1151436-95, 359 EPA III manual High speed jet H, Correctly adjusted carburetor

Page 31

MAINTENANCE

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance.

The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position.The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H- jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.024 inch (0.6 mm) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents English 357XP EPA I 359 EPASymbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingFelling cut Freeing a trapped tree Freeing a tree that has fallen badlyCutting trees and branches that are in tension Cutting the trunk into logs How to avoid kickbackWhat is kickback? General adviceCarburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorImmediately Checking the brake triggerMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Air filterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning When making adjustmentsElectrical carburetor heating Temperature 0C 32F or colderWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data050 Bar and chain combinations058 Saw chain filing and file gauges Repair or Replacement of Parts Repair or Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1151436-95
Top Page Image Contents