Husqvarna 355FX, 355FXT, 355RX, 355FRM manual Assembly, Assembling the handlebar and throttle

Page 13

ASSEMBLY

Assembling the handlebar and throttle

CAUTION! Some models have the throttle handle fitted at the factory.

•Remove the screw at the rear of the throttle handle.

•Slide the throttle handle onto the right side of the handlebar, (see diagram).

•Align the screw hole in the throttle handle with the hole in the handlebar.

•Refit the screw in the hole in the rear of the throttle handle.

•Screw the screw through the handle and handlebar. Tighten it.

•Unscrew the knob from the handlebar mounting.

•Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

•Put on the harness and hang the machine from the support hook. Now make a final adjustment so that the machine is in a comfortable working position when it hangs from the harness.

•Tighten the knob.

Transport position, handlebar

•The handlebar can easily be turned to fit along the shaft for easier transportation and storage.

•Loosen the knob.Turn the handlebar clockwise so that the throttle handle rests against the engine.

•Now twist the handlebar around the shaft. Tighten the knob.

•Fit the transport guard to the cutting attachment.

Assembling the cutting equipment

WARNING!

!When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 355FX 355FXT 355RX Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? 355RX What is WHAT?What is what on the clearing saw? 355FX, 355FXT Personal protective equipment General Safety PrecautionsStop switch Machine′s safety equipmentThrottle lockout Vibration damping system Cutting attachment guardQuick release MufflerLocking screw Locking nutCutting equipment Cutting equipmentSharpening grass cutters and grass blades Trimmer head Sharpening the saw bladeAssembling the handlebar and throttle AssemblyTransport position, handlebar Assembling the cutting equipment355FX, 355FXT Fitting the blade guard and saw blade355RX Fitting other guards and cutting attachments Safety release Adjusting the harness and clearing sawAdjusting the harness Triobalance harnessCorrect balance Correct heightFuel Handling Fuel safetyFuel Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingHeated handles Working Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceCorrectly adjusted carburetor Fine adjustment of the idle speed TAdjusting the start throttle speed 355RX MufflerCooling system Cleaning the air filterAir filter Bevel gearTemperature -5C 23F or colder Temperature 0C 32F or colderSpark plug Winter useMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataCentre hole in blades/cutters, Ø 25,4 mm Your Warranty Rights and Obligations Federal Emission Control Warranty StatementTrimmy SII Page Auto T45, T45x ´z+REQ¶5*¨ Page 1150374-95 ´z+REQ¶5*¨ ´z+REQ¶5*¨
Top Page Image Contents