Husqvarna YTH20B42T Unassembled Parts, Assembly, To Remove Tractor from Carton, Unpack Carton

Page 5

UNASSEMBLED PARTS

Slope Sheet

Key

(1) Oil Drain Tube

(2) Keys

ASSEMBLY

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping puposes.

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

CHECK BATTERY (See Fig. 1)

Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (L) (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

L

02931

FIG. 1

ADJUST SEAT (See Fig. 2)

Sit in seat.

Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

Release lever to lock seat in position.

A

FIG. 2

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

Raise attachment lift lever to its highest position.

5

Image 5
Contents YTH20B42T Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills Check Engine OIL LevelAutomatic Transmission Warm UP To Start Engine See FigPurge Transmission Mowing Tips Before Each USE MaintenanceLubrication Chart Tractor BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs To Level Mower Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig To Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Remove Hood and Grill Assembly See FigTo Adjust Choke Control To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH20B42T 96043002002, Product no 43 SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis 37 532 40 57-89 Fender Drive Tractor - Model Number YTH20B42T 96043002002, Product no 43 Steering Assembly Engine Seat Assembly KEY Part Description DecalsWheels and Tires Mower Deck KEY Part NO. NO. Description Mower Lift Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement 532 40 57-49 03.15.06 TR
Related manuals
Manual 44 pages 3.56 Kb