Husqvarna YTH2042XP Unassembled Parts, Assembly, To Remove Tractor from Carton, Unpack Carton

Page 5

UNASSEMBLED PARTS

Battery

(2) Hex Bolts 1/4-20 x 3/4

(2) Keps Nut 1/4-20

(1) Oil Drain Tube

Slope Sheet

Key

(2) Keys

ASSEMBLY

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping puposes.

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

CONNECT BATTERY (See Figs. 1)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

DISCARD TERMINAL

PROTECTIVE CAPS

HEX BOLT

KEPS NUT

POSITIVE (RED)

CABLE

TERMINAL

COVER

NEGATIVE (BLACK)

CABLE

02954

•Lift hood to raised position.

•Remove terminal protective caps and discard.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions).

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

FIG. 1

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents YTH2042XP Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Before Each USE MaintenanceTractor BatteryBrake Operation TiresEngine To Remove Mower See Fig Service and AdjustmentsCleaning To Level Mower To Install Mower See FigsMower Drive Belt Removal To Replace Mower Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Tractor Model NO. YTH2042XP 96041000300, Product no 41 SchematicElectrical KEY Part NO. NO. Description Chassis KEY Part Description Drive KEY Part NO. NO. Description Steering Assembly Engine Spark Arrester KITSeat Assembly Wheels and Tires DecalsMower Deck Tractor Model NO.YTH2042XP 96041000300, Product no 41KEY Part NO. NO. Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement
Top Page Image Contents