Husqvarna YTH2042 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

Depress brake pedal fully and set parking brake.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 17)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Roll belt off engine pulley (M) and belt keepers (G).

Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

Remove clutch cable spring (Q) from idler arm (R).

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

Q R

P

K

TO INSTALL MOWER (See Fig. 17–20)

Be sure tractor is on level surface and engage parking brake.

Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

Repeat on opposite side of tractor.

G M F

G

A E

B

C

L D

FIG. 17

18

Image 18
Contents 917.287520 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Cleaning IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Motion Drive BeltBelt Removal To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2042Decals Wheels and TiresKEY Part Description Electrical KEY Part NO. NO. Description Chassis KEY Part Description Drive Tractor Model NO. YTH2042 Steering Assembly Mower Lift 9098 100Engine Optional EquipmentEngine Power Rating Information Mower Deck Tractor Model NO. YTH2042 Seat Assembly Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 06-58 01.03.07 TH
Related manuals
Manual 44 pages 46.3 Kb