Husqvarna YTH1842 owner manual HOW to USE Your Tractor

Page 11

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while op- erating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 6)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

Depress clutch/brake pedal into full “BRAKE” position and hold.

Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely,as described above,before leav- ing the operator's position; to empty grass catcher, etc.

 

ATTACHMENT CLUTCH LEVER

THROTTLE/CHOKE

"ENGAGED" POSITION

 

CONTROL

IGNITION

 

 

KEY

 

"DISENGAGED"

 

POSITION

 

PARKING BRAKE

"BRAKE"

"ENGAGED"

POSITION

POSITION

 

MOTION

 

CONTROL

 

LEVER

CLUTCH/BRAKE PEDAL

PARKING BRAKE

"DRIVE" POSITION

"DISENGAGED" POSITION

FIG. 6

STOPPING (See Fig. 6)

MOWER BLADES -

To stop mower blades,move attachment clutch lever to “DISENGAGED” position.

GROUND DRIVE -

To stop ground drive, depress clutch/brake pedal into full “BRAKE” position.

Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

ENGINE -

Move throttle control between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.

Turn ignition key to “OFF” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

TO USE THROTTLE CONTROL (See Fig. 6)

Always operate engine at full throttle.

Operating engine at less than full throttle reduces the battery charging rate.

Full throttle offers the best bagging and mower perfor- mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 6)

The direction and speed of movement is controlled by the motion control lever.

Start tractor with motion control lever in neutral (N) position.

Release parking brake.

Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 6)

The position of the attachment lift lever determines the cutting height.

Grasp lift lever.

Press plunger with thumb and move lever to desired position.

The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain

11conditions.

Image 11
Contents YTH1842 II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Replacing Battery See FigsTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model NO. YTH1842 YTH1842A, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive CRD Steering Assembly Repair Parts 532 14 Seat Seat AssemblyWheels & Tires DecalsEngine KEY Part NO. NO. Description Mower Deck 532 18 Mower Lift Repair Parts Service Notes Service Notes Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 52-00 Rev 01.21.03 RH