Husqvarna YTH1542XP To Replace Mower Blade Drive Belt See Fig, To Check and Adjust Brake See Fig

Page 20

SERVICE AND ADJUSTMENTS

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE OF MOWER

BOTTOM EDGE OF MOWER

TO GROUND

00598

TO GROUND

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

A

GROUND LINE

A

FIG. 16

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.The two front links must remain equal in length.

When distance “D”is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

01268

MANDREL

“D”“D”

FIG. 18

NUT “E”

NUT “F”

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Work belt around both mandrel pulleys and idler pulleys.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower (See "To Install Mower" in this section of manual).

MANDREL PULLEY IDLER

PULLEYS

MANDREL

PULLEY

FIG. 20

TO CHECK AND ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved

20surface, then brake must be checked and adjusted.

Image 20
Contents YTH1542XP Safety Rules Safety Rules Table of Contents Battery Unassembled PartsSteering Wheel Seat Slope SheetAssembly Install Seat See Fig Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Cruise ControlTo Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsMaintenance Service DatesGeneral Recommendations Before Each USETractor Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransmission REMOVAL/EPLACEMENT To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Replace Fuse To Replace Headlight BulbInterlocks and Relays To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model NO. YTH1542XP HAU15H42H, Product no 17Electrical KEY Part NO. NO. Description Chassis and Enclosures 30 532 19 18-15 Fender Tractor Model NO. YTH1542XP HAU15H42H, Product no 17 DriveKEY Part Description Steering Assembly KEY Part NO. NO. Description Engine Optional EquipmentSeat Assembly Decals Wheels & TiresMower Lift 532 18 88-22 Pin GrooveMower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 18-52 02.25.04 RD