Husqvarna PZ29 CE manual Belts, Replacing Pump Belt, Belt Removal, Belt Installation

Page 45

MAINTENANCE

5.Adjust belt tension by turning the eyebolt until there is approximately 22.2 mm-25.4mm ( 7/8" -1") of threads showing outside the nut.

6.Belt tension should be set to 60-70 lbs.

7.Replace belt shields on both mandrel housings and secure with fasteners.

Pump Belt

The belts are not adjustable. Replace belts if they begin to slip from wear.

Replacing Pump Belt

Park the mower on a level surface. Engage the parking brake.

Belt Removal

1.Remove the deck belt (see Deck Belt Removal in this section of the manual).

2.Remove clutch stop to access the belt.

3.Disconnect clutch wire.

4.With a ½" breaker bar and using the square opening in the idler arm, shift the arm to create slack in the belt.

5.Remove belt from the engine and pump pulleys.

Belt Installation

1.Wrap the belt around the engine pulley.

2.Wrap the belt around the left pump pulley.

3.Route the belt around the inside of the idler pulley.

4.With a ½" breaker bar and using the square opening in the idler arm, shift the arm to create slack in the belt.

While holding the idler back with the breaker bar, wrap the belt around the right pump pulley.

5.Replace and secure clutch stop.

6.Reinstall the deck belt. (See Deck Belt Installation in this section of the manual).

V-belts

Check every 100 hours of operation. Check for severe cracking and large nicks.

NOTE: The belt will show some small cracks in normal operation.

8065-054

Adjust belt tension

3

1

2

8065-041

1.Electric clutch

2.Idler release placement

3.Clutch stop

Pump belt removal

45

Image 45
Contents Operator Manual All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and DecalsRemove key before Performing any Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentBe extra cautious when driving on slopes Safe Handling of Gasoline General Maintenance Risk of sparking Transport Spark Arrestors Rollover Protection System RopsControl Locations ControlsMotion Control Levers Blade Switch Parking BrakeThrottle Control Ignition Switch Choke Control FusesHour Meter Cutting Height Pedals Tracking KnobSeat Adjustment Lever Seat should not be adjusted while unit is in motionFuel Shut Off Valve Fuel Tank Operation TrainingSteering Before Starting Roll Bar and Safety BeltStarting the Engine Set the throttle Open the fuel tank valve Set the engine speed Weak Battery Jumper Cables UseTo remove cables, reverse order Running Operating on Hills Mowing Tips Stopping the Engine Bypass Valves Moving Machine By HandMaintenance Maintenance Battery For cleaningFor replacing Safety System Fuel FilterTire Pressures Parking brake adjustment Measure gap Deck Belt Installation Deck BeltDeck Belt Removal Pump Belt Belt InstallationBelts Replacing Pump BeltCutting Blades Leveling Deck Adjusting the Mower DeckCaster Wheels Removal and InstallationAnti-scalp Rollers Deck Lift SpringCleaning Use protective glasses when cleaning and washingHardware Lubrication Lubrication ScheduleGeneral Cables Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsFluid and Filter Change Hydraulic DriveTransmission Purging Procedures Problem Cause TroubleshootingTroubleshooting Service StorageWinter Storage Wiring Diagram PZ29CE Technical DataEngine TransmissionPZ29CE Cm Flat Deck Combi Deck Frame DimensionVibrations Noise EmissionsTorque Specifications Standard HardwareMetric Standard Hardware EU Declaration of Conformity Information Conformity CertificatesOnly applicable to European versions Business Name and AddressDelivery Service Service JournalAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Service Journal Page 115 460427 Rev B 2012-01-16