Husqvarna LTH1797 owner manual Connect Battery See Figs

Page 7

ASSEMBLY

SEAT SHOULDER

BOLT

SEAT PAN

FLAT WASHER

02464

ADJUSTMENT

KNOB

FIG. 2

CONNECT BATTERY (See Figs. 3 and 4)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Remove terminal protective caps and discard.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions).

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

 

DISCARD TERMINAL

 

 

PROTECTIVE CAPS

 

TERMINAL

KEPS

 

NUT

HEX BOLT

COVER

 

02604

 

POSITIVE (RED)

NEGATIVE (BLACK)

CABLE

CABLE

 

FIG. 3

SEAT PAN

 

 

LABEL

02602

FIG. 4

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents LTH1797 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIII. Children ServiceIV. Towing Table of Contents Key BatteryUnassembled Parts Steering Wheel SeatBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonConnect Battery See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs Before Starting the EngineTo Operate Mower See Fig To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Lubrication Chart MaintenanceCheck Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust BrakeTo Check Brake Front Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor Model NO. LTH1797 96011022101, Product no 11 SchematicElectrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive CRD Steering Assembly Repair Parts Optional Equipment EngineSpark Arrester Seat Assembly Wheels & Tires Decals5531 Mower LiftMower Deck Repair Parts Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationStatementwarranty
Top Page Image Contents