SERVICE AND ADJUSTMENTS
TO ATTACH JUMPER CABLES -
•Connect one end of the RED cable to the POSITIVE
(+)terminal of each
•Connect one end of the BLACK cable to the NEGATIVE
•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
•BLACK cable first from chassis and then from the fully charged battery.
•RED cable last from both batteries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEAK OR DEAD |
| FULLY CHARGED | ||||||||||||||||||||||||
BATTERY |
| BATTERY | ||||||||||||||||||||||||
FIG. 26
REPLACING BATTERY (See Fig. 27)
WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparking from acci- dental grounding.
•Lift hood to raised position.
•Remove terminal guard.
•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.
•Install new battery with terminals in same position as old battery.
•Reinstall terminal guard.
•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.
•Connect BLACK grounding cable to negative
•Close terminal access doors.
•Close hood.
TO REPLACE HEADLIGHT BULB
•Raise hood.
•Pull bulb holder out of the hole in the backside of the grill.
•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
•Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.
•Check wiring. See electrical wiring diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp
TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)
•Raise hood.
•Unsnap headlight wire connector.
•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.
•To replace, reverse above procedure.
HOOD
HEADLIGHT WIRE
CONNECTOR
02495
FIG. 28
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.
KEPS NUT
TERMINAL
ACCESS
DOOR
TERMINAL
GUARD
HEX BOLT
POSITIVE (RED)
CABLE
NEGATIVE (BLACK)
CABLE
TO ADJUST CHOKE CONTROL
The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair
FIG. 27
and/or adjustment.
23