Husqvarna 2042 LS Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

Depress brake pedal fully and set parking brake.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 17)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Roll belt off engine pulley (M) and belt keepers (G).

Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

Remove clutch cable spring (Q) from idler arm (R).

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 17–21)

Be sure tractor is on level surface and engage parking brake.

Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

Repeat on opposite side of tractor.

 

M

F

G

 

R

 

G

 

 

Q

A

 

 

E

 

 

P

B

C

K

D

 

L

FIG. 17

 

 

18

Image 18
Contents 2042 LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig To USE Throttle Control D See FigSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigReverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionMaintenance Lubrication ChartTires TractorBrake Operation Blade CareEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Schematic SCH12Electrical KEY Part Description Chassis Tractor - Model Number 2042LS 96043004200, Product no 43 Drive 532 40 53-84 Transaxle, Tufftorq K46BT 171 872 11 Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering 532 18 Seat Assembly Decals Wheels and TiresMower Deck 116 117 119 118 188 189 145116 Tractor - Model Number 2042LS 96043004200, Product no 43 Mower Lift 100Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 81-29 Rev 12.03.07 AP