Husqvarna LGT24K54 owner manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 24

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 41)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Movemotioncontrollevertotheneutral(lockgate)position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4" to 1/2" in the direc- tion it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

Fig. 41

TO START ENGINE WITH A WEAK BATTERY (See Fig. 42)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 42

REPLACING BATTERY (See Fig. 43)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal cover.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal cover.

•First connect RED battery cable to positive (+) battery terminal with bolt and nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining bolt and nut. Tighten securely

•Close hood.

NEGATIVE (BLACK)

CABLE

TERMINAL

COVER

POSITIVE (RED)

CABLE

Fig. 43

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LGT24K54 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Rear 3/16 Lift Link Shoulder Bolt 1/4 O.DOil Drain Tube 4 O.DAssembly Tools Required for AssemblyBefore Removing Tractor from Skid Install ANTI-SWAY BAR S if Equipped See Turn Steering Wheel Left and Position Mower See FigANTI-SWAY BAR S Attach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigAttach Front Link E See Fig Install Belt on Engine Clutch Pulley M See Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To Operate MowerTo Stop Mower Blades Reverse Operation System ROSTo Operate on Hills To Transport See FigsService REMINDER/HOUR Meter Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install MowerTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigVisual SIDE-TO-SIDE Adjustment See Fig Precision SIDE-TO-SIDE Adjustment See FigTo Level Mower To Replace Motion Drive Belt See Fig To Check BrakeTo Remove Wheel for Repairs See Fig Front Wheel TOE-IN/CAMBERTransaxle Motion Control Lever Neutral Adjustment See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Attach Jumper CablesTransmission Other Fuel SystemEngine OIL CylindersTroubleshooting Problem Cause CorrectionTo run when oper Battery will notFires when turn Engine continuesSchematic Tractor Model NO. LGT24K54 96043012700, Product no 43Tractor Model NO. LGT24K54 96043012700, Product no 43 Electrical KEY Part DescriptionChassis Tractor Model NO. LGT24K54 96043012700, Product no 43 Drive Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Engine KEY Part NO. NO. DescriptionSteering Assembly Decals Wheels and TiresSeat Assembly Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ 11.24.10 TH
Related manuals
Manual 48 pages 32.06 Kb

LGT24K54 specifications

The Husqvarna LGT24K54 is a robust lawn tractor designed to meet the needs of homeowners who value both performance and comfort. It brings together cutting-edge technology and user-friendly features, making it a smart choice for maintaining lawns of various sizes.

One of the standout features of the LGT24K54 is its powerful 24 HP engine. The engine is a high-performance Kohler unit, providing ample power to tackle even the toughest grass and terrains. This ensures that users can complete their mowing tasks efficiently without worrying about whether their equipment can handle the job.

The tractor is equipped with a 54-inch cutting deck, which allows for a wide cutting path. This feature means mowing can be accomplished faster than with smaller decks, making it ideal for larger yards. The cutting height is adjustable, ranging from 1.5 inches to 4 inches, accommodating different grass types and personal preferences.

Husqvarna has introduced several technologies in the LGT24K54 to enhance the user experience. It features an ergonomic steering wheel and seat that provide comfort during extended use. In addition, the easy-to-use dashboard includes intuitive controls for engaging the cutting deck, adjusting speed, and more, ensuring that even novice users can operate the mower with ease.

Another impressive characteristic of the LGT24K54 is its hydrostatic transmission. This feature allows for seamless speed variations and provides a smooth driving experience without the need for manual gear shifting. It makes navigating around obstacles and tight corners much simpler.

The tractor also has a wide range of optional accessories, including baggers, mulch kits, and front attachments, making it a versatile machine throughout the year. Whether you need to collect grass clippings or tackle snow in winter, the LGT24K54 can adapt to your needs.

In terms of durability, the Jonsered LGT24K54 comes with a heavy-duty frame and steel cutting deck, ensuring long-lasting performance even in demanding conditions. The reinforced construction helps resist wear and tear, so users can depend on their equipment year after year.

In conclusion, the Husqvarna LGT24K54 is a powerful and versatile lawn tractor that combines robust engineering with user-friendly features. Ideal for homeowners looking for efficiency and comfort, it brings together advanced technologies and smart design to ensure a pleasant mowing experience and a pristine lawn.
Top Page Image Contents