Husqvarna GTH2554XP owner manual With attachment clutch

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires” when

1.

Engine throttle control not set between half and

1.

Move throttle control between half and full speed

turning engine “OFF”

 

full speed (fast) position before stopping engine.

 

(fast) position before stopping engine.

 

 

 

 

 

 

 

 

 

 

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents GTH2554XP Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B Install Mower and Drive Belt See To Attach Nose Roller See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal To Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor - Model NO. GTH2554XP GTH2554XPA, Product no 56Electrical KEY Part Description Chassis and Enclosures 138Repair Parts Ground Drive 153Transaxle Hydro Gear Steering Assembly Repair Parts Engine Repair Parts Seat Assembly 532 18 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 82-18 Rev 8.4.04 TR/MH/rad/MH

GTH2554XP specifications

The Husqvarna GTH2554XP is a robust and versatile riding lawn mower designed for homeowners who seek efficiency and power in their lawn care routine. This mower is equipped with a powerful 24 HP Briggs & Stratton engine that delivers excellent performance, ensuring that it can tackle even the most challenging terrains with ease. The engine is paired with a hydrostatic transmission, which allows for smooth and effortless speed adjustments without the need for manual gear shifting.

One of the standout features of the GTH2554XP is its cutting deck. The 54-inch cutting deck is designed to provide a wide cutting path, reducing the time required to mow larger areas. The deck is made from high-quality stamped steel, ensuring durability and longevity. Additionally, it comes with a cutting height adjustment feature that allows users to choose from multiple height settings, ensuring a precise cut tailored to their lawn’s needs.

The mower is also designed with comfort in mind. Its ergonomic steering wheel and adjustable seat allow the operator to maintain a comfortable posture during extended mowing sessions. The high-back seat provides excellent lumbar support, making it suitable for long hours of work. Furthermore, the mower features cruise control, enabling users to maintain a steady speed without having to keep their foot on the pedal, thus reducing fatigue.

Another impressive aspect of the Husqvarna GTH2554XP is its innovative technology integration. It is compatible with various attachment options, including mulching kits and baggers, making it a versatile choice for lawn care. The mower’s compact design makes it maneuverable around tight corners and flower beds, providing an efficient mowing experience.

Safety is also a priority with the Husqvarna GTH2554XP; it is equipped with a motion detector that automatically shuts off the engine if the operator leaves the seat. This feature adds an extra layer of safety, especially in households with children or pets.

Overall, the Husqvarna GTH2554XP combines power, comfort, and advanced features to deliver an exceptional mowing experience. Its robust build, efficient engine, and innovative technology make it an ideal choice for homeowners who value quality and performance in their lawn maintenance equipment. Whether tackling a small yard or a larger property, the GTH2554XP stands out as a reliable and efficient solution.
Top Page Image Contents