Husqvarna GTH27V48LS Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 22)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Remove mower belt from electric clutch pulley (M). See Mower Drive Belt Removal in "TO REPLACE MOWER BLADE DRIVE BELT" in this section.

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER (See Fig. 22-29)

Ensure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to its lowest position.

CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED)

ANTI-SWAY BAR (S)
TOWARDS	TOWARDS
TRANSAXLE	MOWER DECK
90° END	INTEGRATED WASHER END

Fig. 23

A

C

D

S

D

M F O P

Q

E

H

B

Fig. 22

18

Image 18

Contents GTH27V48LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigTo Start Engine with a Weak Battery see FIG Replacing Battery See FigTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionEngine continues Decals Wheels and TiresKEY Part Description Schematic SCH12Electrical KEY Part Description Chassis 189Tractor Model NO. GTH27V48LS 96043011700, Product no 43 Drive G7-BCBB-1XDC-1FCA 30!2+ª!22%34%2ª+4 EngineEngine Power Rating Information Steering Assembly Seat Assembly Mower Deck Tractor Model NO. GTH27V48LS 96043011700, Product no 43 Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX10.21.10 TH