Husqvarna GTH2254XP owner manual Know Your Tractor

Page 11

OPERATION

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR.

Compare the illustrations with your tractor to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

 

 

 

 

LIGHT SWITCH

 

 

 

HOURMETER

POSITION

 

AMMETER

IGNITION

 

 

 

 

 

 

SWITCH

 

ATTACHMENT

 

 

 

 

 

CHOKE

 

 

CLUTCH SWITCH

THROTTLE

CONTROL

 

 

 

CONTROL

 

 

 

 

BRAKE PEDAL

 

 

 

LIFT LEVER

 

 

 

PLUNGER

 

 

 

 

 

 

 

0

 

MOTION DRIVE

 

60

60

 

 

TECH

AMPS

 

 

 

 

 

BELT TENSION

 

 

 

LIFT LEVER

HANDLE

 

 

 

 

 

 

 

 

 

 

 

PARKING

 

 

 

 

BRAKE LEVER

FREEWHEEL

 

HEIGHT ADJUSTMENT

MOTION

CONTROL

 

CONTROL

 

 

KNOB

 

LEVER

 

 

 

 

02711

FIG. 7

Our tractors conform to the safety standards of the American National Standards Institute.

ATTACHMENT CLUTCH SWITCH - Used to engage mower blades or other attachments mounted to your tractor.

LIFT LEVER - Used to raise and lower mower deck or other attachments mounted to your tractor.

BRAKE PEDAL - Used for braking the tractor and starting the engine.

THROTTLE CONTROL - Used to control engine speed.

FREEWHEEL CONTROL - Disengages transmission for pushing or slowly towing the tractor with the engine off.

IGNITION SWITCH - Used to start and stop the engine.

AMMETER - Indicates battery charging(+) or discharg- ing(-).

MOTION CONTROL LEVER - Selects the speed and direction of tractor.

CHOKE CONTROL - Used when starting a cold engine.

LIGHT SWITCH POSITION- Turns the headlights on and off.

LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its position.

PARKING BRAKE LEVER - Locks brake pedal into the brake position.

HEIGHT ADJUSTMENT KNOB - Used to adjust the mower height.

MOTION DRIVE BELT TENSION HANDLE - Used when changing motion drive belt and, if necessary, starting engine under extremely cold conditions.

HOURMETER - Indicates hours of operation.

11

Image 11
Contents GTH2254XP III. Children IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See a and 4B To Attach Nose Roller See Fig Install Mower and Drive Belt SeeCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingMower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor - Model NO. GTH2254XP GTH2254XPA, Product no 57 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts 153 Ground Drive532 14 Bracket Shift Steering Assembly Repair Parts Engine Repair Parts 532 18 Seat Seat AssemblyDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement 532 18 85-48 Rev 8.3.04 RD/rad/MH