Husqvarna Detailed Tiller Parts Diagram and Essential Storage Maintenance for Optimal Performance

Page 16

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

Clean entire tiller (See “CLEANING” in the Maintenance section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent.

NOTE: Fuel stablizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stablizer container. Run engine at least 10 minutes after adding stablizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug.

Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

Pull starter handle slowly several times to distribute oil.

Replace with new spark plug.

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your unit indoors and cover it to give protection from dust and dirt.

Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

16

Image 16
Contents FT900 Safety Rules Maintenance and StorageTraining PreparationTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack Unpack Carton & Install Handle See Fig Install Depth Stake Assembly See FigHandle Height Tilling WidthOperation Meets Ansi Safety RequirementsKnow Your Tiller HOW to USE Your Tiller Stopping See FigTine Operation See Fig TillingBefore Starting Engine To TransportFill Engine with OIL See Fig ADD GasolineTilling Hints Breaking in Your TillerCultivating Maintenance Schedule MaintenanceGeneral Recommendations AIR Cleaner See Fig EngineCleaning Cooling System See FigMuffler Spark PlugService and Adjustments To Adjust Handle Height See FigTiller Tine ArrangementTine Operation Check See Fig To Remove Belt Guard See FigTo Replace V-BELTS See Figs Check Tine Operation To Adjust CarburetorReplace Belt Guard Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionHandle Assembly KEY Part DescriptionBelt Guard and Pulley Assembly Wheel and Depth Stake Assembly  Tine Assembly Tineipb3KEY Part NO. NO. Description Decals Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ 11.29.10 CL
Related manuals
Manual 28 pages 57.26 Kb