Husqvarna GTH2248XP owner manual 36 532 18 67-99 Tie Rod

Page 37

REPAIR PARTS

TRACTOR - MODEL NO. GTH2248XP (GTH2248XPB), PRODUCT NO. 954 56 78-88

STEERING ASSEMBLY

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 16 66-27

Wheel, Steering

2

532 17 85-57 Axle Asm., Front

3

532 12 48-36

Fitting, Grease

4532 16 18-49 Spindle Asm, LH

5532 16 18-48 Spindle Asm., RH

6532 12 49-31 Bearing, Race Thrust Harden

7532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.

8812 00 00-29 Ring, Klip #T5304-75

9

532 12 12-32 Cap, Spindle

10874 78 10-44 Bolt, Fin Hex 5/8-11 x 2-3/4

11532 13 65-18 Spacer Brg Axle Front 1.570

12873 90 10-00 Nut, Lock Flange 5/8-11 Unc

13532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.

14810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8

15532 12 47-01 Nut Lock Center 3/8-24 Unf

16532 14 51-03 Shaft Asm., Steering

18532 17 55-72 Draglink, Ball Joint Solid Vgt

19532 15 60-11 Support Asm., Steering Vgt

20

532 17 75-92

Boot Steering

21

532 15 99-45

Adapter, Wheel Steering

22

532 15 51-05

Bushing, Strg.

23

532 15 29-27

Screw

25874 78 06-16 Bolt, Fin Hex 3/8-16 x 1 Gr. 5

26532 16 66-26 Cap , Wheel Steering

27532 12 49-37 Bearing, Col. Strg.

28817 00 06-12 Screw 3/8-16 x 3/4

29

532 10 42-39 Bearing, Flange

31532 13 81-36 Bushing, Nyliner Snap

32819 11 16-10 Washer 11/32 x 1 x 10 Ga.

33810 04 05-00 Washer, Lock Hvy Hlcl Spr 5/16

34874 78 05-12 Bolt, Hex Hd 5/16-18 x 3/4

35532 13 80-59 Gear, Sector Steering

36 532 18 67-99 Tie Rod

41532 15 52-46 Bracket Switch Inerlock VGT97

42817 49 05-08 Screw 5/16-18 x 1/2

44532 17 75-93 Extension Steering Premium

45819 13 24-11 Washer 13/32 x 1-1/20 x 11 Ga.

46819 13 16-10 Washer Flat 13/32 x 1 x 10 Ga.

47532 17 94-71 Bracket Asm. Idler

48817 06 06-12 Screw 3/8-16 x .75

49

532 17 58-20

Pulley Idler Flat

50

873 90 06-00

Nut Lock Flg 3/8-16 Unc

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

37

Image 37
Contents GTH2248XP General Operation IV. ServiceII. Slope Operation III. ChildrenSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model NO. GTH2248XP GTH2248XPB, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground Drive532 14 Bracket Shift Steering Assembly 36 532 18 67-99 Tie Rod Engine Repair Parts Lift Assembly Repair Parts Seat Assembly Wheels & Tires DecalsMower Decb Mower Deck Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationRantywar Tementsta 532 18 47-58 Rev 05.21.03 RD/TR