Husqvarna YTH24V48LS owner manual To Replace Motion Drive Belt See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 37)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Remove belt from stationary idler (C) and clutching idler (D).

5.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

6.Remove belt downward from engine pulley and around electric clutch (G).

7.Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

G

H

B

A

C

J

D

F

Fig. 37

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

4.Install belt through stationary idler (C) and clutching idler (D).

5.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

6.Reconnect clutch harness (A).

7.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

8.Install mower (See “TO INSTALL MOWER” section in this manual).

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL (See Fig. 38)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 38

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH24V48LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionEngine continues Wheels and Tires DecalsKEY Part Description Schematic SCH12Tractor Model NO. YTH24V48LS 96043011600, Product no 43 Electrical Chassis 234Tractor Model NO. YTH24V48LS 96043011600, Product no 43 Drive Nut U Chnl 1/4-20 550DP .350 PNL Engine Spark Arrester KITSeat Assembly Steering Assembly 532 41 Wheel, Steering 532 19 Mower Deck Tractor Model NO. YTH24V48LS 96043011600, Product no 43 Mower Lift    Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX11.09.10 BAD
Top Page Image Contents