Husqvarna YTH2548 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

“B”“B”

FIG. 22

BOTH FRONT PLATE LINKS MUST BE

 

EQUAL IN LENGTH

NUT “D”

NUT “C”

 

TRUNNION

FRONT PLATE

 

ASSEMBLY

 

FIG. 23

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents YTH2548 IV. Service Safety RulesGeneral Operation II. Slope Operation NN Ordere to Prevent Acci Table of Contents Mower Unassembled PartsTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Hourmeter Indicates hours of operation Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak BATTERYSee Fig To Remove Wheel for Repairs See FigTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWhen operator leaves seat Service Notes Tractor Model NO. YTH2548 YTH2548A, Product no 57 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Drive KEY Part Description Steering Assembly KEY Part NO. NO. Description KEY Part NO. no Description NO. NO. Description Seat AssemblyWheels & Tires DecalsEngine Mower Lift Mower Deck Repair Parts Fold Along This Dotted Line Degree Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement 532 18 99-11 Rev 6.8.04 MH
Top Page Image Contents