Husqvarna YTH2748 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

3/4" wrenches

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

Remove locknut and large flat washer from steering shaft.

Position front wheels of the tractor so they are pointing straight forward.

Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING WHEEL INSERT

LOCK NUT

LARGE FLAT WASHER

STEERING

WHEEL ADAPTOR

STEERING WHEEL

STEERING

71

SHAFT

27

 

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment knob securely.

6

Image 6
Contents YTH2748 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Secondary Drive Belt See Fig Mower Drive Belt InstallationTo Replace Mower Drive Belt Remove Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2748 96013001000, Product no 13Electrical KEY Part NO. NO. Description Chassis Tractor Model NO. YTH2748 96013001000, Product no 13 Drive Tractor Model NO. YTH2748 96013001000, Product no 13 Steering Assembly Tractor Model NO. YTH2748 96013001000, Product no 13 Seat Assembly Decals Wheels and TiresEngine Tractor Model NO. YTH2748 96013001000, Product no 13 Mower Lift Tractor Model NO. YTH2748 96013001000, Product no 13 Mower Deck Tractor Model NO. YTH2748 96013001000, Product no 13 Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 54-05 12.17.04 TR