Renesas M306H2T-RPD-E manuals

76 pages717.24 Kb

3Preface
To use the product properly
- Precautions for Safety
When using outside Japan
4Contents
Chapter 1. Precautions for Safety
9 WARNING IMPORTANT
CAUTION
- Note on Malfunctions in the PC4701 System:
- 10WARNING
  - Warning for Installation:
  - Warnings for Use Environment:
  - Caution to Be Taken for Modifying This Product:
  - Cautions to Be Taken for Handling This Product:
  - 11Notes on Downloading Firmware:
  - Notes on Target System:
  - Note on When the Emulator Debugger Ends:
  - Note on Final Evaluation:
  - Notes on Stack Area:
  - 12Note on Setting the Work Area:
  - Notes on MAP References and Settings:
  - 13Note on RESET* Input:
  - Note on Clock Supply to the MCU:
  - Note on HOLD* Input:
  - Notes on NMI* Input:
  - Note on RDY* Input:
  - 14Note on Software Reset:
  - Notes on Address Match Interrupt:
  - Notes on Interruption:
  - Note on BRK Instruction and BRK Instruction Interruption:
  - Note on Stop and Wait Modes:
  - Note on Address 00000h Access:
  - 15Note on Protect Resistor (PRC2):
  - Note on Commands that Access the Single-step Interrupt Vector Area:
  - Notes on Software Breaks and Hardware Breaks:
  - Note on DMA Transfer:
  - 16Notes on Pullup Control Resistor:
  - Note on Reading Internal Resources of an MCU:
  - Notes on Watchdog Function:
  - 17Note on Differences between Actual MCUs and the Emulator:
    - 18Table 1.3 Differences of outputs between actual MCUs and this product (when executing program)
    - 19Table 1.4 Differences of outputs between actual MCUs and this product (in stop mode)
    - Table 1.5 Differences of outputs between actual MCUs and this product (in wait mode)
    - Table 1.6 Outputs of this product when the user program is stopping
- 22Chapter 2. Preparation
  - 2.1 Terminology
  - 232.2 Package Components
  - 2.3 Other Tool Products Required for Development
  - 242.4 Name of Each Part
    - (1) System Configuration
    - 25(2) Inside of the Emulation Pod
  - 262.5 When Using the Emulator for the First Time
- 28Chapter 3. Setting Up
  - 3.1 Removing the Upper Cover
  - When Removing the Upper Cover:
    - 30Table 3.1 Switch settings of the M306H2T-RPD-E (1/4)
    - Table 3.2 Switch settings of the M306H2T-RPD-E (2/4)
      - Switch Signal Setting Description
      - system. (Uses P8 6 /X COUT pin as port P8
      - P86/XCOUTSW5
      - SW4 P8
      - Connects the P87/XCIN pin of MCU to the target system. (Uses P8 7/XCIN pin as port P8
      - system. (Uses P86/XCOUT pin as XCOUT and connect XCOUT to the target system)
      - system. (Uses P86/XCOUT pin as XCOUT and opens X
      - Uses P87/XCIN pin as XCIN.
  - 31Note on Switch Settings:
    - 32Table 3.3 Switch settings of the M306H2T-RPD-E (3/4)
    - 33Table 3.4 Switch settings of the M306H2T-RPD-E (4/4)
    - 3.3 Selecting Clock Supply
  - 35Notes on Changing the Clock Supply:
    - (1) Using the Oscillator Circuit on the Target System
  - 36Notes on External Clock:
    - 38(3) Replacing the Oscillator Circuit Boards
    - 3.4 A-D Conversion Bypass Capacitor
  - 39Note on the A-D Converter:
    - 3.6 Connecting the PC4701
      - (1) Connecting the Cable to the PC4701
  - 41Note on Connecting the Cable:
  - Note on Securing the Screws:
    - 3.7 Connecting the Target System
  - 43Notes on Connecting the Target System:
    - 443.8 Making an MCU File for PD30
- 46Chapter 4. Usage
  - 4.1 Turning On the Power
    - (1) Checking the Connection of the Emulator System
    - (2) Turning On the Power
  - Notes on Power Supply:
    - (3) LED Display When PC4701 Starts Up Normally
  - 47Note on Memory Expansion and Microprocessor Modes:
  - Note on CLOCK LED:
    - 4.2 Downloading Firmware
      - (1) When It is Necessary to Download Firmware
      - (2) Downloading Firmware in the Maintenance Mode
  - 48Note on Downloading Firmware:
    - 4.3 Self-checks
      - (1) Self-check Procedure
      - (2) If an Error is Detected in Self-checks
  - 49Note on Self-checks:
- 52Chapter 5. Specifications
  - 5.1 Specifications
  - 535.2 Operation Timing in the Memory Expansion and Microprocessor Modes (5 V)
    - (1) Separate Bus, No-Wait
      - *1 Calculated by the following formula according to the frequency of BCLK.
      - 54Figure 5.1 Memory expansion and microprocessor modes (no-wait)
    - 55(2) Separate Bus, With Wait, Accessing External Memory Area
      - *1 Calculated by the following formula according to the frequency of BCLK.
      - 56Figure 5.2 Memory expansion and microprocessor modes (with wait)
    - 57(3) Multiplex Bus, With Wait, Accessing External Memory Area
      - *2 Calculated by the following formulas accord- ing to the frequency of BCLK.
      - *1 Calculated by the following formulas accord- ing to the frequency of BCLK.
      - 58Figure 5.3 Memory expansion and microprocessor modes (with wait, multiplex bus)
    - 59(4) Timing Requirements
      - Figure 5.4 Timing requirements
      - *1 Minimum 7 ns (The definition is different from that of actual MCUs. For details, see Figure 5.5.)
      - 60Figure 5.5 Timing requirements
  - 615.3 Electrical Characteristics
  - 625.4 Connection Diagram
- 66Chapter 6. Troubleshooting
  - 6.1 Flowchart to Remedy the Troubles
    - Figure 6.1 Flowchart to remedy troubles
  - 676.2 When the Emulator Debugger Does Not Start Up Properly
    - (1) When the LED Display of the PC4701 is Abnormal
      - Table 6.1 LED's abnormal display and its checkpoints
        See the user's manual of the PC4701.
        See "3.6 Connecting the PC4701" (page 41).
        See the CLK command of the emulator debugger.
        See "3.3 Selecting Clock Supply" (page 35).
        See "3.2 Setting Switches and Pullup Resistors" (page 29).
    - 68(2) Errors Occur When the Emulator Debugger Starts Up (When the target system is connected)
      - Table 6.2 Checkpoints of errors when starting up the emulator debugger (target is connected)
    - 69(3) Errors Occur When the Emulator Debugger Starts Up (When the target system is not connected)
      - Table 6.3 Checkpoints of errors when starting up the emulator debugger (target is not connected)
  - 706.3 Operation Differs from That of Actual MCUs
- 72Chapter 7. Maintenance and Guarantee
  - 7.1 Maintenance
  - 7.2 Guarantee
  - 7.3 Repair Provisions
  - 7.4 How to Request for Repair
  - 73Note on Transporting the Product: