3M X90W Regarding the indicator lamps

66

Troubleshooting

Regarding the indicator lamps

/LJKWLQJDQGÀDVKLQJRIWKH32:(5LQGLFDWRUWKH/$03LQGLFDWRUDQGWKH7(03

indicator have the meanings as described in the table below. Please follow the

instructions within the table. If the same indication is displayed after the remedy,

or if an indication other than the following is displayed, please contact your dealer

or service company.

POWER

indicator

LAMP

indicator

TEMP

indicator Description

Lighting

In Orange

Turned

off

Turned

off

The projector is in a standby state.

Please refer to the section “Power On/Off”.

Blinking

In Green

Turned

off

Turned

off

The projector is warming up.

Please wait.

Lighting

In Green

Turned

off

Turned

off

The projector is in an on state.

Ordinary operations may be performed.

Blinking

In Orange

Turned

off

Turned

off

The projector is cooling down.

Please wait.

Blinking

In Red

(discre-

tionary)

(discre-

tionary)

The projector is cooling down. A certain error

has been detected.

3OHDVHZDLWXQWLOWKH32:(5LQGLFDWRU¿QLVKHV

blinking, and then perform the proper measure using

the item descriptions below.

Blinking

In Red

or

Lighting

In Red

Lighting

In Red

Turned

off

The lamp does not light, and there is a

possibility that interior portion has become

heated.

Please turn the power off, and allow the projector to

cool down at least 20 minutes. After the projector has

VXI¿FLHQWO\FRROHGGRZQSOHDVHPDNHFRQ¿UPDWLRQRI

the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

,VWKHDLU¿OWHUGLUW\"

• Does the peripheral temperature exceed 35°C?

If the same indication is displayed after the remedy,

please change the lamp referring to the section “Lamp”.

Blinking

In Red

or

Lighting

In Red

Blinking

In Red

Turned

off

7KHODPSGRRUKDVQRWEHHQSURSHUO\¿[HG

Please turn the power off, and allow the projector to

cool down at least 45 minutes. After the projector has

VXI¿FLHQWO\FRROHGGRZQSOHDVHPDNHFRQ¿UPDWLRQRI

the attachment state of the lamp door. After performing

any needed maintenance, turn the power on again.

If the same indication is displayed after the remedy,

please contact your dealer or service company.

© 3M 2006. 3M™ Digital Projector X90w

Contents

Main Digital Projector X90w Operator's Guide About this manual Content Fastening the lens cover 1. 2. 3. Projector features Preparations Contents of package Part names Projector Control panel Rear panel Remote control Setting up Arrangement Adjusting the projector's elevator 1. 2. 3. 4. 5. Using the security bar and slot Connecting your devices Connecting your devices (continued) Inserting an SD card and USB memory 1. 2. 3. 4. How to use the slot cover lock 1. 2. Connecting power supply 1. 2. Putting batteries 1. 2. 3. Laser pointer Remote control Changing the frequency of remote control signal About the remote control signal Using as a wired remote control NOTE Using as a simple PC mouse & keyboard Power on/off Turning on the power 1. 2. 3. 2. 3. 1. 2. Temporarily muting the sound 1. Selecting an input signal 1. Searching an input signal 1. Selecting an aspect ratio 1. Adjusting the zoom and focus 1. 2. Adjusting the lens shift 1. 2. Using the automatic adjustment feature 2. 2. Correcting the keystone distortions 1. Using the magnify feature 2. Freezing the screen 1. Temporarily blanking the screen 1. Using the menu function 1. 2. 3. 3. 4. 2. EASY Menu EASY Menu (continued) PICTURE Menu Page PICTURE Menu (continued) IMAGE Menu From the IMAGE menu, items shown in the table below IMAGE Menu (continued) INPUT Menu From the INPUT menu, items shown in the table below can Page Page RESOLUTION The resolution for the RGB1 and RGB2 input signals can be set on this projector. SETUP Menu From the SETUP menu, items shown in the table below SETUP Menu (continued) AUDIO Menu From the AUDIO menu, items shown in the table below can SCREEN Menu From the SCREEN menu, items shown in the table below Page Page Page OPTION Menu Page Page Page Page 1. Using Security Features 1.1 Inputting the PASSWORD 1.2 Changing the PASSWORD 1.3 If you have forgotten your PASSWORD 2. Using the MyScreen PASSWORD Function 2.1 Turning on the MyScreen PASSWORD Function 2.2 Setting the PASSWORD 2.3 Turning the PASSWORD off 3. Using the PIN LOCK Function 3.1 Registering the PIN Code 3.2 Turning Off the PIN LOCK Function 3.3 If you have forgotten your PIN Code 4. Using the Transition Detector Function 4.1 Turning On the Transition Detector Function 4.2 Setting the Transition Detector PASSWORD Page MIU Menu Page Page Page INFORMATION SERVICE Maintenance Lamp 2. 3. 4. 5. 6. Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE 1. 2. 3. 4. 5. 9. 1. 2. 3. 4. 5. 1. 2. 1. 2. Other care Troubleshooting Related messages There is no input signal. The horizontal or vertical frequency of the input signal LVQRWZLWKLQWKHVSHFLHGUDQJH The internal temperature is rising. $QRWHRISUHFDXWLRQZKHQFOHDQLQJWKHDLUOWHU Regarding the indicator lamps The projector is in a standby state. The projector is warming up. The projector is in an on state. The projector is cooling down. Regarding the indicator lamps (continued) The cooling fan is not operating. There is a possibility that the interior portion has become heated. ,WLVWLPHWRFOHDQWKHDLUOWHU There is a possibility that the interior portion has become overcooled. 1. 2. 3. Page Phenomena that may be easy to be mistaken for machine defects (continued) 6SHFLFDWLRQ NOTE7KHVHVSHFLFDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH