AT-50LD
AT-50CWLD
Caller ID with Large Display
Important: To receive information about incoming telephone calls, you must sub- scribe to the Caller ID and/or Call Waiting services provided by your local telephone company; there is a fee for this service and it may not be available in all areas.
BATTERY INSTALLATION
Before operating your Caller ID install 4 alkaline batteries in the AT50LD or 2 alkaline batteries in the AT50CWLD in the battery compartment located on the bottom of the unit. The screw must be remooved to open the battery door. Using the illustration, observe battery polarity (+ or
WARNING: Your Caller ID must be disconnected from the telephone line
before inserting or changing batteries.
1.Turn the unit over.
2.Remove the screw from the battery door and lift the battery door away from the base.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AAA |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||||
AAA |
|
| AAA | AAA | |||||||||
➥ |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3.Insert the batteries as shown.
4.Replace the battery door and screw. (Be sure to tigten the screw completely.)
SETTING THE LANGUAGE
Your caller ID unit can display messages in English, French and Spanish. The default language setting is English. After inserting the batteries do the following:
1.When English is displayed after inserting batteries, select language English French/Spanish using the REVIEW.5.key. Each press of the REVIEW 5 key will change the displayed language.
2.Press the DELETE not REVIEW 2 to set the displayed language.
SETTING THE LOCAL AREA CODE (AT- 50CWLD only)
After selecting a language for the display, you’ll need to program your area code in to the unit so it can properly recognize and dial calls using he CALLBACK feature.
If you are in an area that doesn’t allow 7 digit dialing enter “010” for the area code. 1.Press the REVIEW 5 or REVIEW 2 key
to select each digit.
2.Press the “DELETE” key to set the number, not the REVIEW key.
3. There will not be a beep comfirmation
Note: When an area code digit is flashing, continue pressing the REVIEW 5 or REVIEW
2key until the correct digit appears. Press DELETE to set the digit.
Note: After the language and area codes are set, should you require changing them press and hold both REVIEW 5 and REVIEW
2keys for approximately 8 seconds. The unit will default to setup mode.
When a new call is received the
DESK AND WALL MOUNTING. Attach the pedestal to the bottom or back of the unit in the desired desk mount position (see illustration). For wall mounting, first detach the pedestal and mount the unit directly to the wall using two screws (not pro- vided)
Desk Mounting Position 1
Desk Mounting Position 2
CONNECTING TO A TELEPHONE 1.Connect the line cord from the wall jack
into the jack marked LINE on the Caller ID. 2.Connect the supplied
line jack on the telephone.
AC adapter to the unit and the wall outlet. 4.Check for a dial tone to ensure proper
connection.
LINE | PHONE |
Note: (AT- 50CWLD only) You must wait for at least 2 rings to get Caller ID data. A telephone does not need to be connected in order for it to work, but is recommended for the callback feature and necessary for the Caller ID on the Call Waiting feature.
CONNECTING TO AN ANSWERING MACHINE
1.Connect the line cord from the wall jack into the jack marked LINE on the Caller ID 2.Connect the supplied
IN jack on your answering machine. 3.Connect a line cord from the answering
machine to the line jack on your tele- phone.
LINE PHONE
Note: The answering machine must be set to answer after at least 2 rings to properly receive Caller ID data.
RECEIVING CALLER ID CALLS
The AT50LD/CWLD will receive and store up to 50 Caller ID calls in the memory. If 50 calls are in the memory, any new calls received will be saved by replacing the old- est in the memory. When a call is received the display will show the following:
*Caller’s Name
*Caller’s Number
*Date and Time of Call
*New Call Indicator
Note: The display will show the name or number from the calling party if available. If the caller’s information is blocked the display will show PRIVATE CALL. If the call informa- tion is not available or outside the calling area, the display will show OUT OF AREA
DELETING CALL RECORDS
To delete a call record, press the REVIEW 5oor 2 key to locate the call record wish to delete. Press DELETE twice quickly and the call record will be removed and the next call in memory will be displayed.
DELETING ALL CALL RECORDS
To delete all records press and hold DELETE key for approximately 8 seconds. All calls will be automatically erased. DELETE ALL will not appear on the screen.
NEW CALLS
When a new call is received the NEW indi- cator will turn on and the LCD display will show the call record information. After 20 seconds the display will show:
*The number of new calls in memory
*The New Call indi-
cator flashing.
The red New Call LED will be flashing to indicate new calls are in memory.
The LED will turn off after all new calls are reviewed.
REVIEWING NEW CALLER ID CALLS If the New Call LED is flashing pressing REVIEW 5 or 2 key to scroll through all new information (newest calls to oldest calls). After the last new call is reviewed, END OF NEW CALL is displayed and the New Call LED turns off.
Note: If all new calls are not reviewed after 20 seconds the display will show the number of new calls remaining in memory. The New Call LED will be flashing.
REVIEWING OLD CALLER ID CALLS When the New Call LED is off, pressing REVIEW 5 key will scroll through all call records from oldest to newest. Pressing the REVIEW 2 key will scroll through all calls newest to oldest. END OF LIST is displayed
between the first and last call record in memory.
Note: After 20 seconds with no keys pressed the date and time screen will be displayed.
RECEIVING REPEAT CALLS
When a call is received more that once the Caller ID will only use one memory location for the call. This will save call memory space.
When a repeat call is received the REPEAT indicator will turn on. The date and time of the call will be updated and the call will be moved from its current memory location to the newest call received.
The REPEAT indicator will be displayed for all repeat calls during NEW CALL review indicating the caller has called more that once.
Note: The New Call counter will not incre- ment for a repeat call.
RECEIVING CALLER ID ON CALL WAITING (AT- 50CWLD only)
The Caller ID will receive name and number of an incoming call while you are on the phone. When a call waiting call is received the display will show the following:
