Abit IC7-MAX3 1-2.Layout Diagram

Introduction	1-3

1-2. Layout Diagram

User’s Manual

Contents

Page Copyright and Warranty Notice 快速安裝指引 IC7-MAX3 のクイックインストールガイドのクイックインストールガイド IC7-MAX3Schnellinstallationsanleitung Краткое руководство по установке IC7-MAX3 Chapter Page IC7-MAX3 快速安裝指引 IC7-MAX3 快速安裝指引將主機板安裝到機殼上安裝記憶體模組 1.找出您主機板上 DIMM 插槽的位置。 DIMM IC7-MAX3 マザーボードをシャーシに取り付ける RAM モジュールの取り付けコネクタ、ヘッダ、スイッチおよびアダプタ電源コネクタを ATX12V 電源コネクタに差し込む BIOS のセットアップ IC7-MAX3Schnellinstallationsanleitung IC7-MAX3Schnellinstallationsanleitung Installieren der Hauptplatine im Gehäuse Installation der RAM-Module 1.Finden Sie den DIMM-Steckplatzauf dem Board Halten Sie ie beiden Ränder des IC7-MAX3Guide d’Installation Rapide Installer la Carte Mre dans le Châssis Installer des Modules RAM 1.Localisez le socle DIMM sur la carte 3.Alignez la touche du cran avec la ligne sur le socle Connecteurs, Socles de connexion, Interrupteurs et Adaptateurs Краткое руководство по установке IC7-MAX3 Установка радиатора и вентилятора охлаждения процессора Page Guida all’installazione veloce Scheda madre IC7-MAX3 Guida all’installazione veloce Scheda madre IC7-MAX3 Installazione della scheda madre sul telaio Installare i moduli RAM 1.Ubicare gli alloggiamenti DIMM sulla scheda 2.Tenere con delicatezza i lati del modulo DIMM senza toccare i connettori Page Chapter 1. Introduction 1-1.Features & Specifications 11.System BIOS 12.Internal I/O Connectors 13.Back Panel I/O 14.Miscellaneous 1-2.Layout Diagram Page Chapter 2. Hardware Setup 2-1.Install The Motherboard 2-2.Install Pentium® 4 CPU and Heatsink Supporting-Base 2-3.Install System Memory Page 2-4.Connectors, Headers and Switches Page Page Page Page Page Page Page (9). System Management Bus Headers (10). Internal Audio Connectors Page Page (13). IDE Connectors (14). Serial ATA Connectors WinXP / Windows .NET Server: OnChip Serial ATA IDE1 IDE2 (15). Status Indicators •D1 (VCC): This LED lights up when the system power is on Page Page Chapter 3. BIOS Setup 3-1.SoftMenu Setup Page 3-2.Standard CMOS Features IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel 3 Master, IDE Channel 4 Master: Back to Standard CMOS Features Setup Menu: [CGA 40]: (Color Graphics Adapter) Power up in 40-columnmode [CGA 80]: (Color Graphics Adapter) Power up in 80-columnmode [Mono]: (Monochrome adapter) Includes high-resolutionmonochrome adapters Halt On: [No Errors]: The system-bootwill not stop for any error detected 3-3.Advanced BIOS Features Page Delay IDE Initial (Secs): PCI Card Support for SMBus: Intel OnScreen Branding: Disable Unused PCI Clock: This option disables the clock of PCI slot that is not in use 3-4.Advanced Chipset Features Memory Hole At 15M-16M: Delay Prior to Thermal: This item selects the delay time before thermal activation AGP Aperture Size: Init Display First: 3-5.Integrated Peripherals OnChip IDE Device: Master/Slave Drive Ultra DMA This item allows you to set the Ultra DMA in use OnChip IDE-2Controller: The description is same as the OnChip IDE-1Controller OnChip Serial ATA Mode: Page OnChip PCI Device: SuperIO Device: Onboard PCI Device: 3-6.Power Management Setup WakeUp by Alarm: Date (of Month) Alarm Time (hh:mm:ss) Alarm This item sets the time you would like the system to power-on POWER ON Function: Page 3-7.PnP/PCI Configurations Allocate IRQ To USB: This item assigns an IRQ for the USB device connected [Enabled]: Automatically assign an IRQ for the USB device connected PCI Latency Timer(CLK): PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No.: 3-8.PC Health Status 3-9.Load Fail-SafeDefaults 3-10.Load Optimized Defaults 3-11.Set Password 3-12.Save & Exit Setup 3-13.Exit Without Saving Page Appendix A. Install Intel Chipset Software Utility A-2 Appendix B. Install Intel Application Accelerator RAID Page Intel Serial ATA RAID Configuration Utility Page Appendix C. Install Audio Driver C-2 Appendix D. Install LAN Driver D-2 Appendix E. Install Silicon Serial ATA RAID Driver E-2 6.Click [Finish] To run the [SATARaid] application, click [Start] [All Programs] [SATARaid] BIOS Setup for Silicon Serial ATA RAID RAID Configuration Utility Menu E-4 Delete RAID set Rebuild Raid1 set This item allows you to rebuild only “Mirrored” RAID set Resolve Conflicts Appendix F. Install USB 2.0 Driver F-2 Appendix G. BIOS Update Guide G-2 7.Flash the BIOS in pure DOS mode A:\>awdflash se6_sw.bin /cc /cd /cp /py /sn /cks /r Note Appendix H. Hardware Monitoring (The Winbond Hardware Doctor Utility) H-2 Appendix H 8.This is the warning message window: Shutdown: Choosing this button will shutdown the computer Help: You can read more information and self-diagnosesimple problems Appendix I. Installation Guide for Suspend to RAM How to use the STR function: Appendix J. Troubleshooting (Need Assistance?) J-2 Q: How can I get a quick response to my request for technical support Example 1: Example 2: CONFIG.SYS: J-3 Main instructions: 1*. MODEL: Note the model number given in your user’s manual Example: IC7-MAX3 Example: REV: Technical Support Form Company Name: Phone Number: Contact Person: Fax Number: Appendix K. How to Get Technical Support alt.comp.periphs.mainboard.abit comp.sys.ibm.pc.hardware.chips alt.comp.hardware.overclocking North America and South America: ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West Fremont, California 94538, U.S.A Tel: Thank You ABIT Computer Corporation