ACCUSPLIT® ALLIANCE625M8D

MULTIMODE TIMER/STOPWATCH

OPERATING INSTRUCTIONS

E RECALLUP/DOWN

BA

RESET/SPLIT

START/STOP

 

 

C MODE

ROTARY

D SET

SWITCH

 

INTRODUCTION

This unit has five modes: Stopwatch, Auto Repeat Countdown Timer, Dual Display CountdownTimer, Pacer, and Preset CountdownTimer.

Press C (MODE) to change between modes. Note:Timing must be stopped and reset to zero to change modes.

3.Press A to start countdown timing

4.Press E to show the time from start ( )

5.Press E again to return to countdown timing ()

6.Press A again to stop counting

7.Press B to return to the original setting

8.When time is up, the unit will beep once, then start counting again.The number of cycles completed is recorded in brackets in upper left of display.

DUAL DISPLAY COUNTDOWN TIMER

1.Press C to move the cursor to point to DUAL

2.Press E to change the dual display timer mode (SU or Id or UP)

3.Press D to adjust the timer on the lower display Press D again to adjust the timer on the upper display

Press B to set hours, E to set minutes, A to set seconds

Press A & B at the same time to reset digits to zero

Press D again to complete the settings

4.SU -Two countdown timers work simultaneously

Press A to start

Press A to stop (STOP: flashes)

Press B to reset to the original settings

Id -Two countdown timers work independently

Press A to start/stop lower display

Press B to start/stop upper display

Press A & B at the same time to reset to the original settings

UP -Two count up timers work independently

Press A to start/stop lower display (STOP: flashes when stopped)

Press B to start/stop upper display (STOP: flashes when stopped)

Press A & B at the same time to reset to zero

MEMORY STOPWATCH

SPLIT TIMING

1.Press C to move the cursor to point to

2.Press A to start stopwatch

3.Press B repeatedly to remember the last 8 splits

Lower display shows cumulative split and upper display shows lap split

After 5 seconds, the unit will unlock splits to display current running split time

4.Press E to recall the last 8 splits

5.Press A to stop counting

6.Press B to reset to zero

START-STOP TIMING

1.Press C to move the cursor to point to

2.Press A to start counting

3.Press A repeatedly to remember the last 8 time-cuts

4.Press E to recall the last 8 times-outs

5.Press A to stop counting

6.Press B to reset to zero

AUTO REPEAT COUNTDOWN TIMER

1.Press C to move the cursor to point to AUTO

2.Press D to enter set mode

Press B to set hours, E to set minutes, A to set seconds

Press A & B at the same time to reset digits to zero

PACER WITH COUNT UP TIMER

1.Press C to move the cursor to point to PACE

2.Press D to adjust the frequency

Press A to increase the digits

Press B to decrease the digits

3.Press A to start pacer

4.Press A again to the stop

5.Press B to reset to zero

6.Press E to turn the pacer’s beep ON or OFF and the symbol (((•))) will appear or disappear

7.Upper display shows count up timer

16 PRESET COUNTDOWN TIMER

1.Press C to move the cursor to point to (1-60)

2.Turn the rotary switch to the desired minutes (1-60)

3.Press A to start countdown timing

4.Press A again to stop countdown timing

5.Alarm Sounds

6.Press B to return to the original setting

To Show Count Up Timing

1.When the time is not up.

a.Press E to check elapsed time ()

b.Press E again to return to countdown ()

2.When the time is over,

a.Press E to check the time from start ( flashes)

b.Press E again to show overtime (flashes)

Page 1
Image 1
Accusplit AL625M8D operating instructions Operating Instructions, Introduction, Memory Stopwatch