Accusplit AX810TTY, AX810TTA Using Time of Day and Alarm, Setting the Watch, Setting the Timer

Pre-alarm is ON

S1 & S4

S3–

In the classroom, theTimeTimer can be used to set time limits, measure the duration of activities and train students to make better use of available time. Use theTimeTimer products to:

•Time standardized tests

•Monitor math and writing speed tests

•Measure study periods and lunch periods

•Regulate computer time

•Administer duration drills

•Show time left to play, get ready or clean up

Using Time of Day and Alarm

Press S2 (upper right) to cycle through the fields you can set.The fields are:Time setting → Alarm On/Off → Pre Alarm On/Off →Time setting (Note that the Pre Alarm can only be set if the Alarm is turned On).

Press S2 until you see digits in the center of the display. Now you can set the timer. Press S3+ (lower right) to increase the timer set point, and press S3– (lower left) to decrease the set point.You will see both the digits and also the dial size increase or decrease.

Setting Notes:

1. You can either press and release S3+ and S3– to

change field values, or “press and hold” either of the

S3 buttons to rapidly change the field value.

Press MODE (lower left) button until the watch shows theTime, displayed both in traditional “analog” form, and also in digital format in center. Notice that the Hour hand is continuously lit, while the minute hand flashes slowly. There is also a second hand sweeping around.

Hour					Minute
hand					hand
	TIME TIMER				flashing
		0	55
	5
1	0			50
		AM
15					45
20				4	0
	25	30	35
		30M
		WATER RESIST

2.	As you pass through each hour while setting, rapid
	advance stops.This helps avoid overshooting your
	desired set point.
3.	The timer can be set to a minimum of 1 minute and a
	maximum of 12 hrs.
4.	You can return to the default timer setting of 60
	minutes by simultaneously pressing S3+ and S3–.

Once you have set the desired time, press S2 once to change Alarm On/Off Setting.You will see the word “ON” or “OFF,” plus an alarm •3 symbol, both flashing. Press S3+ or S3– to turn the Alarm on or off.

If you have turned the Alarm ON, you can now change the Pre-Alarm settings by pressing S2 again. Again, the

PressTIMER (upper right) button to see theTime of Day alarm setting.The watch returns to current time after a few seconds. Or, press MODE twice to see current time immediately.

When theTime of Day alarm sounds, press any button to silence it.

To change the settings forTime of Day orTime of Day Alarm, see the instructions below.

Setting the Watch

The watch uses a standard setting procedure to set all modes. It works as follows:

•Press and hold “S1” to enter setting mode

•Press “S2” to change the field to set

•Press “S3” to change the value of the field being set

•Press “S4” to exit setting mode

Pre-Alarm can only be set if the Alarm is ON. If the Alarm is OFF, pressing S2 will return you to theTime setting field. In Pre-Alarm set, you will see the word “ON” or “OFF,” plusTWO alarm •3 symbols.The Pre-Alarm symbol (smaller and on the left) will be flashing, along with ON or OFF. Press S3+ or S3– to turn the Pre-Alarm on or off.

Pressing S2 again will return you to theTimer setting. Press S4 once (upper left) to exit setting mode. Leaving the watch unattended for 30 seconds in set mode causes it to save any changes and then exit set mode.

Setting the Current Time of Day and Time of Day Alarm

Press MODE (lower left) to change toTime of Day mode. Press and hold S1 (upper left) until the Hour “hand” and digits begin to flash, indicating that you have entered set mode.

Press S2 (upper right) to cycle through the fields you can

Setting the Timer

The timer must be stopped before changing settings.

To set the timer, first press the MODE button until you see theTimeTimer’s red dial display appear. Press and hold the S1 button (upper left) for about three seconds, until

the numbers in the middle begin to flash, indicating that you have entered setting mode.

	TIME TIMER				S2
		0	55
	5
1	0			50
15					45
		. .
20				4	0
	25	30	35
		30M			S3+
		WATER RESIST

Alarm is ON

set.The fields are: Hour → Minute → Second → (Time of Day) Alarm On/Off → Alarm Hour → Alarm Minute → Hour

Press S2 until the Hour hand and digits are flashing. Set the current Hour by pressing S3+ (lower right) to increase the Hour setting, or pressing S3– (lower left) to decrease the setting. Note that the watch has “AM” and “PM” indicators.

Note: You can either press and release S3+ and S3– to change field values, or “press and hold” either of the S3 buttons to rapidly change the field value.