Acer 1100 Series

Chapter 2 - BIOS Utility 2-5

2.2.2 Processor Speed

The Processor Speed parameter specifies the speed of the CPU currently installed

in your system. The system supports Intel Pentium II CPUs running at 400 or 450

MHz.

2.2.3 Bus Frequency

The Bus Frequency parameter specifies the system external clock. The bus

frequency should always be set to 100 MHz.

2.2.4 Internal Cache

This parameter specifies the first-level or the internal memory size (i.e., the

memory integrated into the CPU), and whether it is enabled or disabled. For

information on how to configure the system memory, see section 2.7.3.

2.2.5 External Cache

This parameter specifies the second-level cache memory size currently supported

by the system, and whether it is enabled or disabled. For information on how to

configure the system memory, see section 2.7.3.

2.2.6 Floppy Drive A

This parameter specifies the type of drive designated as Floppy Drive A. For

information on how to configure the floppy drives, see section 2.4.1.

Contents

Main Page iii Join Us to Fight Against Piracy Page Page CD-ROM Safety Warning FCC Class B Radio Frequency Interference Statement Table of Contents Chapter 1 System Board Chapter 2 BIOS Utility Page Chapter 3 System Housing Index List of Figures List of Tables About This Manual Manual Structure Chapter 1 System Board Chapter 2 BIOS Utility Chapter 3 System Housing Conventions Chapter 1 System Board 1.1 Features Page 1.2 Major Components 1.3 System Board Layout Page 1.4.2 Jumper Settings * Default Table 1-1 lists the system board jumpers with their corresponding settings and functions. Table 1-1 System Board Jumper Settings 1.4.3 Connector Functions Table 1-2 lists the different connectors on the system board and their respective functions. Table 1-2 Connector Functions Table 1-2 Connector Functions (continued) Page 1.6 Installing Optional Components 1.6.1 ESD Precautions 1.6.2 Pre-installation Instructions 1.6.3 Post-installation Instructions 1.7 Installing the Pentium II Processor Page Page 1.9 Installing the Termination Board 1.10 Memory Upgrade 1.10.1 Memory Configurations 1.10.2 Installing a DIMM 1.10.3 Removing a DIMM 1.10.4 Reconfiguring the System 1.11 Installing Expansion Cards 1.11.1 Installing 32 Bit PCI Cards 1.11.2 Installing an AGP Card 1.12 ASM Pro 1.13 Remote Diagnostic Management 1.13.1 Installing the RDM Module Page 1.14 Error Messages 1.14.1 Software Error Messages 1.14.2 System Error Messages Table 1-4 System Error Messages Table 1-4 System Error Messages (continued) 1.14.3 Correcting Error Conditions Chapter 2 BIOS Utility 2.1 Entering Setup Page 2.2 System Information 2.2.1 Processor Page Page Page Page 2.3 Product Information 2.3.1 Product Name 2.3.2 System S/N Page 2.4 Disk Drives Page Page If there is no device connected, choose None. Hard Disk Block Mode Advanced PIO Mode Hard Disk Size > 504 MB Page 2.5 Power Management 2.5.1 Power Management Mode IDE Hard Disk Standby Timer System Sleep Timer 2.5.2 Power Switch < 4 sec. 2.5.3 Wakeup Event Modem Ring 2.6 Startup Configuration 2.6.1 Fast POST Mode Page Page 2.7 Advanced Configuration 2.7.1 Onboard Devices Configuration Serial Port 1 Serial Port 2 Parallel Port 3BCh 378h 278h Page Operation Mode Onboard Floppy Disk Controller Onboard IDE Primary Channel Page 2.7.2 PnP/PCI System Configuration PCI IRQ Setting PCI Device Latency Timer PCI IRQ Sharing Page VGA Palette Snoop Graphics Aperture Size Plug and Play OS Reset Resource Assignments 2.7.3 Memory/Cache Configuration Internal Cache (CPU Cache) Cache Scheme Page 2.7.4 CPU Speed Configuration Bus Frequency Multiple Processor Speed 2.7.5 System Event Configuration System Event Logging View Event Logs Event Control Threshold Settings 2.8 System Security Setup 2.8.1 Disk Drive Control 2.8.2 Setup Password Setting a Password Changing or Removing the Setup Password Bypassing the Setup Password 2.8.3 Power-on Password Operation Mode Page 2.9 Date and Time 2.9.1 Date 2.9.2 Time 2.10 Remote Diagnostic Configuration Page 2.11 Load Setup Default Settings 2.12 Abort Settings Change 2.13 Leaving Setup Chapter 3 System Housing Page Page Altos 1100 Series Users Guide 3-4 3.2.2 Rear Panel Chapter 3 System Housing 3-5 3.2.3 Internal Structure The figure below shows the housing internal structure and some of the basic system components. Page 3.3.2 Left Panel 3.4 Installing Disk Drives 3.4.1 3.5-inch Drive 3.4.2 5.25-inch Drives Page Page Page Page 3.6.1 Jumpers and Connectors The following diagram shows the SCSI jumpers and connectors. * Default JP4 3.6.2 SCSI Backplane Board Index A B C D E F H I J L N O P R S T W