ADTRAN NetVanta ADSL quick start ATM Commands, ATM SUB-INTERFACE Commands

®

Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com.

NetVanta ADSL Network Interface Module (ADSL over ISDN) P/N 1200889E1/L1

ADSL NIM COMMANDS

retrain

Forces the modem to retrain.

snr-margin [showtime monitor l training monitor] <margin>

Enables monitoring and sets the minimum signal-to-noise (SNR) ratio during training and showtime. Use the no form of this command to disable monitoring.

showtime monitor	Enables margin monitoring to retrain the ADSL
	interface if the specified minimum margin is
	violated during showtime.
training monitor	Enables margin monitoring to retrain the ADSL
	interface if the specified minimum margin is
	violated during training.
<margin>	Sets the minimum SNR margin in dB. Range is
	1 to 15.

training-mode [G.DMT G.LITE Multi-Mode T1.413 ADSL ADSL2+ READSL2]

Configures the ADSL training mode. This setting must match the service provider’s DSLAM.

G.DMT	Specifies ANSI full-rate mode. This is the only
	training mode valid on the ADSL Annex B.

ATM COMMANDS

snmp trap link-status

Controls the Simple Network Management Protocol (SNMP) variable ifLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface to send SNMP traps when there is an interface status change. Use the no form of this command to disable this trap.

See the AOS Command Reference Guide on the ADTRAN OS System Documentation CD for a complete list of ATM commands.

ATM SUB-INTERFACE COMMANDS

access-policy <policyname>

Assigns a specified access policy for the inbound traffic on an interface. Use the no form of this command to remove an access policy association.

<policyname> Identifies the configured access policy using an alphanumeric descriptor (all access policy descriptors are case-sensitive).

dynamic-dns [dyndns dyndns-custom dyndns-static] <hostname> <username> <password>

Configures Dynamic DNS service provided by Dynamic Network Services, Inc. (www.dyndns.org).

dyndns	Allows you to alias a dynamic IP address to a static
	hostname in various domains. This service is provided
	for up to five hostnames.
dyndns-custom	Gives complete control over an entire domain name. A
	web-based interface provides two levels of control
	(basic or advanced) over the domain. Can be used
	with both static and dynamic IPs.
dyndns-static	Allows a hostname such as yourname.dyndns.org to
	point to your IP address. This service is provided for
	up to five hostnames.

encapsulation [aal5mux aal5snap]

Configures the encapsulation type for the ATM Adaption Layer (AAL) of the ATM Protocol Reference Model.

aal5mux	Specifies encapsulation type for multiplexed virtual
	circuits. A protocol must be specified.
aal5snap	Specifies encapsulation type that supports LLC/SNAP
	protocols.

oam-pvc managed <frequency>

Enables end-to-end F5 Operation, Administration, and Maintenance (OAM) loopback cell generation and OAM management for an ATM interface. Use the no form of this command to disable generation of OAM loopback cells.

<frequency> Specifies the time delay between transmitting OAM loopback cells. Range is 0 to 600 seconds.

oam retry <up-count> <down-count> <retry-frequency>

Configures parameters related to OAM management for an ATM interface. Use the no form of this command to disable OAM management parameters.

<up-count>	Specifies number of consecutive end-to-end F5 OAM
	loopback cell responses that must be received in order
	to change a PVC connection state to up. Range is
	1 to 255.
<down-count>	Specifies number of consecutive end-to-end F5 OAM
	loopback cell responses that are not received in order
	to change a PVC state to down. Range is 1 to 255.
<retry-frequency>	Specifies frequency (in seconds) that end-to-end F5
	OAM loopback cells are transmitted when a change in
	the up/down state of a PVC is being verified. Range is
	1 to 600.

Quick Start Guide, 61200889E1-13D, July 2006 ADTRAN Technical Support +1-256-963-8716 Copyright © 2006 ADTRAN, All Rights Reserved