ADTRAN SHDSL V.35 LTU manual SHDSL V. 35 LTU, Jobaid, Total Access, Shdsl, Interface Connections

TOTAL ACCESS	®	3000 SHDSL V. 35 LTU	JOBAID
			61182008L5-22A
			0202

TOTAL ACCESS 3000 SHDSL V.35 LTU

SHDSL

1182008L5

N

x 6 4 K

RX

PWR

FRONT PANEL LED INDICATORS

PWR	● Off	No power
	● Green	Self-test passed and the module is In Service
	● Yellow	Self-test passed and the module is Out of Service
SHDSL ● Off		SHDSL Loop is Out of Service -- Unassigned
	● Green	SHDSL Loop is trained
G.703	● Red	SHDSL Loop is not trained
	● Off	G.703 port is not configured, Out of Service -- Unassigned, or in alarm
		condition
Nx64k	● Green	G.703 port configured and no alarms
	● Off	Service is not configured or in alarm condition
RTS	● Green	Service is configured and operating normally
	● Off	Nx64k service not configured or RTS control line is OFF
RLSD	● Green	RTS control line is ON
	● Off	Nx64k service not configured or RLSD control line is OFF
TST	● Green	RLSD control line is ON
	● Off	Module is not in loopback or BERT
	● Green	Local loopback is active, or BERT running with no errors
	✷ Blinking Yellow	Module is running a BERT with bit errors
ALM	● Red	BERT running with no pattern sync
	● Off	No alarm condition detected
	● Yellow	Remote alarm condition detected
	● Red	Alarm condition detected locally

V.35 PORT PIN ASSIGNMENTS

V.35 Port
Circuit No.	Circuit Name	To/From DCE	Pinout (A/B)
102	Signal Ground		B
103	Transmit Data	To	P/S
104	Receive Data	From	R/T
105	Request To Send	To	C

DEFAULT PROVISIONING OPTIONS

Provisioning		Options	Default
Unit Options
Cross-Connect Map			All Idle
Local Management		Disabled, Enabled	Enabled
LT Mode Clk Source		Internal Clock	Internal Clock
		Nx64 ETC
		G.703 RX Clock
NTU Auto Provisioning		Disabled, Enabled	Disabled
External Port Alarms		Disabled, Enabled	Enabled
Line Card Service State		In Service	Out of Service - Unassigned
	Out of Service - Maintenance
	Out of Service - Unassigned
G.703 Port Service State		In Service	Out of Service - Unassigned
	Out of Service - Maintenance
	Out of Service - Unassigned
Nx64K Port Service State		In Service	Out of Service - Unassigned
	Out of Service - Maintenance
	Out of Service - Unassigned
SHDSL Options
Rate (Kbps)	Enter a new value for N from 3 to 36,		2056 (N=32)
	where Rate(Kbps)=(N x 64) + 8:
SNR Margin Alarm Threshold(dB)		Disabled, Enabled	Disabled
Loop Attenuation Alarm Threshold (dB)		Disabled, Enabled	Disabled
Test Options
Loopback Timeout(Min)		Disabled, Enabled	Disabled
BERT Test Pattern		All Zeros	2e15-1
		All Ones
		2e15-1
		2e23-1 2e15-1

G.703

SHDSL

106 Clear To Send From D

BERT Test Pattern Polarity Normal, Inverted Normal

G.703

Nx64K

TX

RTS

RLSD

TST

ALM

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

107	Data Set Ready	From	E
108/2	Data Terminal Ready	To	H
109	Received Line Signal Detect	From	F
113	Transmit Signal Element Timing	To	U/W
114	Transmit Signal Element Timing	From	Y/AA
115	Receive Signal Element Timing	From	V/X
140	Remote Loopback	To	N
141	Local Loopback	To	L
142	Test Indicator	From	NN

INTERFACE CONNECTIONS

The G.703 signal is transmitted to the network either via the Total Access 3000 backplane connectors or the two BNC connectors mounted on the faceplate. The G.703 signal and the SHDSL signal use the following backplane amphenol connector Pairs:

■SHDSL - Pair 2

■G.703 Tx - Pair 8

■G.703 Rx- Pair 7

Nx64K In-band Pattern Detection Disabled, Enabled Disabled

COMPLIANCECaution: Up to -200 VDC may be present on telecommunications wiring.

This product is intended for installation in restricted access locations only and in equipment with a Type “B” or “E” enclosure.

Code	Input	Output
Power Code (PC)	F	C
Telecommunication Code (TC)	–	X
Installation Code (IC)	A	–

HANDLING PRECAUTIONS REQUIRED. ■ For a complete Installation and Maintenance faxback: (877) 457-5007, Document #766. Please have your fax number available. ■