DC MODULE CONNECTORS

Installation Guide

Standard Connector (P/N 5060-3386)

Relay Connector (P/N 5060-3387)

General Information

Load connections are made on the connector supplied with each module. The connector is fastened to the back of the mainframe. Modules can then be installed or removed from the mainframe without disturbing the wiring on the connector.

The connector has a switch to select either local or remote voltage sensing, depending on how the load is connected.

+Sense used to connect the + remote sense lead. Set the sense switch to Remote when this connection is used.

-Senseused to connect the - remote sense lead. Set the sense switch to Remote when this connection is used.

GND used for signal ground (GND) connections.

A relay connector is identified by a check mark on the Relay label on the connector. Relay connectors include load and sense disconnect and polarity reversal relays.

Making Load Connections

Load connections are the same on both the standard and the relay connector.

Open the Connector

Open the connector by loosening the four corner screws (M3 X 10 mm).

CAUTION ∙ Hand tighten only.

∙ Start all screws before tightening.

∙ Tighten screws evenly.

∙ DO NOT overtighten screws.

∙DO NOT use locking-type adhesive on the screws.

A five-terminal barrier block is provided for wire connections. The barrier block screws are 6-32 x 1/4 inch (equivalent p/n 2470-0001). The barrier block terminals are labeled as follows:

+Output used to connect the + output load wire.

-Outputused to conect the - output load wire.

Connect the Wires

Loosen the barrier block screws and connect the wires. The barrier block accepts spade or ring terminals. You can also connect a stripped wire to the barrier block.

Twist the wire around under the screw terminal and tighten the screw.

TIE

WRAP

Route the wires out of the bottom of the connector as shown in the figure above. Use the tie-wrap supplied with the connector to secure the wires to the connector.

Close the Connector

Close the connector and tighten the four corner screws. Observe the CAUTION on the figure.

Attach the Connector to the Mainframe

Attach the connector to the back of the module on the mainframe at the appropriate slot location. Tighten the two screws (M3 x 10mm) on the connector. Observe the

CAUTION on the figure.

Agilent p/n 5959-3366

May, 2000

Microfiche p/n 5959-3367

 

Page 1 Page 2
Page 1
Image 1
Agilent Technologies 5060-3386, 5060-3387 manual DC Module Connectors, Installation Guide, General Information
Page 1 Page 2

5060-3386, 5060-3387 specifications

Agilent Technologies, a leader in advanced measurement solutions, offers a range of products catering to various analytical needs. Among these products are the Agilent 5060-3387 and 5060-3386, which are essential components in the field of chemical analysis and spectroscopy.

The Agilent 5060-3387 is a highly regarded detector module designed for use with gas chromatography (GC). It features a high sensitivity that enables the detection of trace amounts of analytes, making it ideal for applications in environmental monitoring, food safety, and pharmaceuticals. One of its key characteristics is the use of advanced ionization techniques that enhance its detection capabilities, allowing for the identification of complex chemical compounds.

Meanwhile, the Agilent 5060-3386 is a robust and versatile detector solution specifically designed for liquid chromatography (LC). Its advanced architecture provides excellent performance across a wide dynamic range, ensuring accurate quantification of compounds even in challenging matrices. The core technology behind the 5060-3386 includes high-efficiency optics and optimized signal processing, which contribute to its impressive resolution and low baseline noise.

Both products are designed with ease of use in mind, featuring user-friendly interfaces and streamlined workflows. This attention to usability ensures that scientists and researchers can focus on their analytical tasks without being hindered by complicated setups or maintenance.

Additionally, the Agilent 5060-3387 and 5060-3386 are built with durability and reliability in mind. They are made from high-quality materials designed to withstand the rigors of daily laboratory use. Furthermore, Agilent Technologies provides extensive support and documentation, empowering users to maximize the performance and longevity of their equipment.

In summary, the Agilent 5060-3387 and 5060-3386 detectors offer advanced technologies and characteristics tailored for gas and liquid chromatography applications, respectively. Their high sensitivity, efficiency, and reliability make them indispensable tools for any analytical laboratory striving for excellence in chemical analysis.
Top Page Image Contents