Aiphone IS-DVF-2RA Wiring Diagram, Relay Board Wiring and Settings, Specifications, FCC Warning

WIRING DIAGRAM: IS-MV IS-CCU

IS-DVF-2RA

CAT-5e

CAT-5e

NO

COM

NC

Board on back of unit

N/O Dry Contact See wiring below

0.5 Amp

IS-PU-UL

RELAY BOARD WIRING AND SETTINGS:

Configuration Switch

See Settings to right

	OFF	ON
		1
Relay 1 Output	NO	2
	C	34
N/O, COM, N/C	NC
Relay 2 Output	NO
	C
N/O, COM, N/C	NC

*Relay 2 External Reset Connect to N/O dry switch

Default Configuration when shipped

Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication. Relay 2 triggers on emergency call and remains on during communication.

	ON	Trigger Source	RY1 Triggered?	RY1 Remains ON	RY2 Triggered?	RY2 Remains ON	RY2 Requires
1				During Talking?		During Talking?	Reset?
2		Normal Call	YES	YES	NO	N/A	N/A
3		Emergency Call	YES	YES	YES	YES	NO
4		Talking	YES	YES	NO	N/A	N/A
		Door Release	NO	N/A	NO	N/A	N/A

Optional Configuration

Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication. Relay 2 triggers on an emergency call and remains on during communication. Relay 2 requires reset.

	ON	Trigger Source	RY1 Triggered?	RY1 Remains ON	RY2 Triggered?	RY2 Remains ON	RY2 Requires
1				During Talking?		During Talking?	Reset?
2		Normal Call	YES	YES	NO	N/A	N/A
3		Emergency Call	YES	YES	YES	YES	YES*
4		Talking	YES	YES	NO	N/A	N/A
		Door Release	NO	N/A	NO	N/A	N/A

Contact Technical Support if additional switch configurations are required.

SPECIFICATIONS:

Camera unit:	CMOS camera
Scanning line:	525 lines
Min. illumination:	5 Lux at 1’6”
Terminations:	RJ45 jack for audio/video
	Screw terminals for door release and relay outputs
Relay rating:	24V AC/DC 0.5A on Door station, 24V AC/DC 1.0A on relay board
Operating Temp:	14° ~ 140°F / -10° ~ 60°C
Wiring Distance:	980’ with Cat5e/6 cable
Dimensions:	11-3/4” H x 7” W
w/SBX-ISDVFRA:	11-11/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)
	FCC WARNING:
	This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference that may cause undesired operation.

•For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable.

•Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Aiphone Corporation	TOLL FREE TECHNICAL SUPPORT:
1700 130th AVE NE * Bellevue, WA 98005
Ph: (800) 692-0200 * Fax: (425) 455-0071	(800) 692-0200
tech@aiphone.com	E-MAIL: tech@aiphone.com

Pg. 2 IS-DVF-2RA Instr. 0411JD