IMPORTANT INSTRUCTIONS - OPERATING MANUAL
WALL BRACKET INSTALLATION (Figures 1 through 4)
NOTE: Always install the bracket to a minimum of 2" x 4" studding.
1. | Insert the |
| CERTAIN THE DIRECTION OF THE FLAG BRACKET is as shown in Figure 1. |
2. | THE HARDWARE TO ATTACH THE WALL BRACKET TO THE WALL STUD IS NOT SUPPLIED. Locate the wall stud nearest to the desired |
IMPORTANT INSTRUCTIONS - OPERATING MANUAL
require the use of a flathead screwdriver to complete assembly. Stand behind the Fan. Slip the flat of the screwdriver between the Front and Rear Grills, next to one of the unfastened hooks. (Figure 6 / Detail B) Pull screwdriver handle upwards towards the Rear Grill. Slip the Front Grill hook over the Rear Grill outer ring with a push. Repeat procedure with remaining hooks.
CAUTION: DO NOT BEND WIRES ON THE FRONT OR THE REAR GRILLS.
| Fan location. Attach the Wall Bracket to the stud using (3) 5/16" diameter x 2" long Lag Screws. |
3. | Position the Flag Bracket in the Motor Neck and align the Pivot Hole with the Larger Hole in the Flag Bracket. (Figure 2) |
4. | Attach pull string to motor speed switch, if desired. |
5. | Insert the 1/2" X 1" Hex Bolt (3/4" head) through the Motor Neck, and the Flag Bracket. Place 1/2" diameter Split Lockwasher then the 1/2" |
| diameter Hex Nut (3/4" head) and tighten fully with 2 adjustable wrenches. (Figure 3) |
6. | From the same side of the Motor Neck,insert one |
| the Flag Bracket. (Figure 3) |
To Fasten: Place one 1/4" Flatwasher, one 1/4" Internal Tooth Lockwasher, a second 1/4" Flatwasher and then tighten the Adjustable Knob over the remaining threads. Final assembly of the Motor to the Wall Mount Bracket is illustrated in Figure 4.
Figure 5 |
Inset A |
Figure 6
Detail A
Top Hooks
Figure 1
Flag Bracket
Figure 2
Placement of Motor to
Flag Bracket
Detail B
Bottom Hooks
Wall Bracket
Motor Neck 
CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED ANYTIME THE CIRCULATOR IS MOUNTED OVERHEAD FOR ADDITIONAL SAFETY.
Figure 7
Large Guard
Wires
Wall Mount Assembly
Figure 3 |
Detailed View of Hardware |
Figure 4
Final Assembly of Motor to
Wall Mount Bracket
Oscillating Motor Shown
SECONDARY SUPPORT CABLE (Figures 7 and 8)
1.Loop one end of Cable around the Large Guard Wires of both the Front and Rear Grills.
2.Attach a Cable Clamp with the "U" on the tail side of the loop leaving a tail approximately 1 to 2 inches. Tighten Clamp Nuts. Make sure no part of the Cable interferes with the Blade.
3.Wrap the other end of the Cable around a secure building joist, truss, or other sup- port near the Fan. Take up all excess slack in the Cable.
CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN.
4.Attach the remaining Cable Clamp as indicated in Step 2. The excess tail should be trimmed to extend 1 to 2 inches past the Clamp.
5.Check the Assembly to assure the Blade is free of all obstructions.
CAUTION: Use of the secondary support cable does not guarantee protection against injury of persons, mounting of both the circulator and cable could fail if subjected to abuse, neglect or improper installation.
Figure 8
Secondary
Support
Cable
GRILL AND BLADE ASSEMBLY (Figures 5 and 6)
NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a
1.Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6)
2.Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft (Inset A) . Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely tighten the Bolt could result in damage to the Fan and/or personal injury.
3.Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Front Grill to Rear Grill by sliding the hooked wires on the Front Grill over the outermost ring on the Rear Grill. (Figure 6 / Detail A). The bottom most hooks will
Rev. A 9/07 | 2 | 5084414 |
OPERATING INSTRUCTIONS
1. TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor:
First pull: High | Second pull: Medium |
Third pull: Low | Fourth pull: OFF NOTE: THIS FAN IS VERY HEAVY. |
Failure to securely hold onto head assembly while adjusting head angle
could result in personal injury.
2.TO ADJUST HEAD ANGLE: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position FIRMLY retighten knob under motor.
NOTE: Motor Head Adjustment Knob and the On/Off Pull Cord have the same location on oscillating or
Rev. A 9/07 | 3 | 5084414 |
