IMPORTANT INSTRUCTIONS - OPERATING MANUAL
CEILING MOUNT INSTALLATION (Figures 1 and 2)
NOTE: Distance mounted from the ceiling can be changed by using a length of
1. | Locate the Pipe Mounting Flange, securely mount to ceiling structure. Ensure ceiling structure can safely support the installed Fan. |
2. Open one tube of Loctite #243 by snapping tube neck just below end cap. Be Certain to follow all warnings noted on Loctite #243 tube. | |
3. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of one end of the Threaded Pipe that will be screwed into the Motor | |
| Mounting Adapter. (Figure 1 - Inset) |
4. | Screw Threaded Pipe into Motor Mounting Adapter. The Threaded Pipe MUST BE screwed in at least 4 full revolutions. Do not |
| allow Loctite #243 to dry before joining. Tighten provided 1/4” Set Screw into Motor Mounting Adapter. (Figure 1) |
5. | Open second tube of Loctite #243 by snapping tube neck just below end cap. Be Certain to follow all warnings noted on Loctite #243 tube. |
6. | Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of the opposite end of the Threaded Pipe that is now screwed into the |
| Motor Mounting Adapter. (Figure 1 - Inset) |
7. | Screw Threaded Pipe with Motor Mounting Adapter to the Pipe Mounting Flange.TheThreaded Pipe with Motor Mounting |
| Adapter MUST BE screwed in at least 4 full revolutions into the Pipe Mounting Flange. Do not allow Loctite #243 to dry before |
| joining. (Figure 1) |
8. | Tighten provided 1/4” Set Screw into Pipe Mounting Flange. (Figure 1) |
IMPORTANT INSTRUCTIONS - OPERATING MANUAL
GRILL AND BLADE ASSEMBLY (Figures 3 and 4)
NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below.
1.Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6)
2.Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to se- curely tighten the Bolt could result in damage to the Fan and/or personal injury.
3.Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Front Grill to Rear Grill by sliding the hooked wires on the Front Grill over the outermost ring on the Rear Grill. (Figure 4 / Detail A). The bottom most hooks will require the use of a flathead screwdriver to complete assembly. Stand behind the Fan. Slip the flat of the screwdriver be- tween the Front and Rear Grills, next to one of the unfastened hooks. (Figure 4 / Detail B) Pull screwdriver handle upwards towards the Rear Grill. Slip the Front Grill hook over the Rear Grill outer ring with a push. Repeat procedure with remaining hooks.
CAUTION: DO NOT BEND WIRES ON THE FRONT OR THE REAR GRILLS.
CAUTION: FAN IS HEAVY AND MAY REQUIRE TWO PEOPLE TO MOUNT.
9. Attach pull string to motor speed switch, if desired
For Oscillating Motor: Place the flat section on the Motor Mounting Adapter next to the Motor Neck. (Figure 2A)
For
10.Insert the 1/2” X 1” Hex Bolt (3/4” head) through the Motor Neck, and the Motor Mounting Adapter. Place 1/2” diameter Split Lock- washer then the 1/2” diameter Hex Nut (3/4” head) and tighten fully with 2 adjustable wrenches.
11.From the same side of the Motor Neck, insert one
To Fasten: Place one 1/4” Flatwasher, one 1/4” Internal Tooth Lockwasher, a second 1/4” Flatwasher and then tighten the Adjustable Knob over the remaining threads.
Inset A |
Detail A Top Hooks
Oscillating Motor View |
Motor Mounting |
Adapter |
Oscillating Motor Shown | Figure 3 |
Detail B |
|
Bottom Hooks | |
Figure 4 | |
Figure 1 |
CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED ANYTIME THE CIRCULATOR IS MOUNTED OVERHEAD FOR ADDITIONAL SAFETY.
Pipe Mounting | Set Screw |
Flange | Inset |
Threaded Pipe | Loctite 243 |
| Application Loctite 243 |
| Set Screw |
Exploded View for Detail |
Figure 2A |
|
Motor Mounting |
Adapter |
secondary support cable (Figure 5)
1.Loop one end of Cable around the Large Guard Wires of both the Front and Rear Grills.
2.Attach a Cable Clamp with the “U” on the tail side of the loop leaving a tail approxi- mately 1 to 2 inches. Tighten Clamp Nuts. Make sure no part of the Cable interferes with the Blade.
3.Wrap the other end of the Cable around a secure building joist, truss, or other support near the Fan. Take up all excess slack in the Cable.
CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN.
4.Attach the remaining Cable Clamp as indicated in Step 2. The excess tail should be trimmed to extend 1 to 2 inches past the Clamp.
5.Check the Assembly to assure the Blade is free of all obstructions.
Large Guard
Wires
Figure 5
| Motor Mounting |
|
|
|
|
|
|
|
|
| |
| Adapter |
|
|
|
|
|
|
|
|
|
|
|
| Ceiling Mount Assembly | |||
|
|
|
| ||
Rev. A 11/07 | 2 | ||||
Exploded View for Detail |
Figure 2B |
5084416 |
CAUTION: Use of the secondary support cable does not guarantee protection against injury of persons, mounting of both the circulator and cable could fail if subjected to abuse, neglect or improper installation.
OPERATING INSTRUCTIONS
1. To Operate: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor:
First pull: High | Second pull: Medium |
Third pull: Low | Fourth pull: OFF NOTE: THIS FAN IS VERY HEAVY. |
Failure to securely hold onto head assembly while adjusting head angle
could result in personal injury.
2.To adjust head angle: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position FIRMLY retighten knob under motor.
NOTE: Motor Head Adjustment Knob and the On/Off Pull Cord have the same location on oscillating or
Rev. A 11/07 | 3 | 5084416 |
