Allied Telesis AT-WDRPS-80 warranty Related Documents, Package Contents, Overview

Related Documents

The Allied Telesyn web site at www.alliedtelesyn.com contains the most recent documentation, software, and technical information for all of our products. For details on the features and functions of your Allied Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our web site:

❑	AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer
	Installation Guide
	PN 613-50367-00
❑	AT-S47 Management Software User’s Guide

To install the AT-WDRPS-80, perform the following procedure:

Note

The AT-WDRPS-80 unit can be installed while the multiplexer is powered ON. You do not need to power OFF the multiplexer to install the RPS.

1.Loosen the two thumbscrews that secure the blank faceplate over the right- hand redundant power supply expansion slot located on the front panel of the AT-WD1008 Multiplexer and remove the cover.

AT-WDRPS-80

Redundant Power Supply (DC)

Installation Guide

Allied Telesyn, Inc.

960 Stewart Drive, Suite B

PN 613-50371-00

Package Contents

Make sure the following items are included in the shipping package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.

❑One AT-WDRPS-80 Redundant Power Supply (DC) Module

❑This installation guide

❑Warranty card

Installing the AT-WDRPS-80 Power Supply

TX			ST
TX
	LNK			RX
	TST	LNK	TST
	TX			TX
RX	WEST RX		TX
		EAST
			RX	TX
		LNK TST
		NORMAL		CH 5
				RX
	SNMP	MODULE		POWER
				SUPPLY B

RX TX

CH 6

EAST TX

RX

RX TX

TX

CH 7 RX

RX

TX
TX	FAN A
CH 8
RX	FAN B

Sunnyvale, CA 94085 USA

Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100 Visit our web site at: www.alliedtelesyn.com

Caution

Before installing the module, refer to the AT-WD1008 Installation Guide for electrical safety and emission information.

2.Remove the AT-WDRPS-80 unit from its shipping package.

3.Slide the AT-WDRPS-80 unit into the RPS expansion slot.

Overview

The AT-WDRPS-80 is a DC Redundant Power Supply (RPS) for the AT-WD1008 Multiplexer chassis. When installed, the unit shares the load of powering the chassis with the standard power supply that comes pre-installed in the chassis. If a power supply fails, the remaining unit provides all power to the system, thereby preventing a network failure. The power supply is hot-swappable, meaning that you can install it while the chassis is powered ON.

Caution

Do not install the AT-WDRPS-80 module in an AT-WD1008 chassis intended for AC power. A DC powered chassis has two DC terminal blocks on the back panel.

TX			ST
TX
	LNK			RX
	TST	LNK TST
	TX			TX
RX	WEST RX		TX
		EAST
			RX		TX
	LNK TST
	NORMAL			CH 5
					RX
	SNMP M			POW		ER
		ODULE			PPLY B

AT-WDRPS-80

POWER

FAULT

RX TX

CH 6

EAST TX

RX

RX TX

TX

CH 7 RX

RX

TX
TX	FAN A
CH 8
RX	FAN B

4.Secure the AT-WDRPS-80 unit to the AT-WD1008 chassis by tightening the two thumbscrews.

AT-WDRPS-80

POWER

FAULT

TX				ST
TX
	LNK			RX
	TST	LNK	TST
	TX			TX
RX	WEST RX		TX
		EAST
			RX	TX
		LNK TST
		NORMAL		CH 5
				RX
	SNMP	MODULE		POWER
				SUPPLY B

RX TX

CH 6 AT-WDRPS-80

EAST

TX

RX

POWER FAULT

RX TX

TX

CH 7 RX

RX

TX
TX	FAN A
CH 8
RX	FAN B

PN 613-50406-00 Rev A 1 2 3